Panasonic KX-TVS90 Page 78 Installation Manual Download | Manualshive

Page: 78 / 410

background image

INTEGRATING THE VPS WITH THE PANASONIC KX-TA SERIES PBX AND KX-TD SERIES PBX

78

Installation Manual

Possible causes of the message: "APT Interface Connection is not Established"

10.

Start up completed.

a)

The Power Indicator light stops blinking when the start-up has been successful. (The
delay varies according to the system’s condition.)

b)

"**ON LINE MODE**"

is displayed.

c)

System prompt [>] is displayed on the screen. To enter system administration,

Press

ENTER

. All parameters can be set through the menu-driven program.

11.

Go

to the

System Administration Top Menu.

Type

[5]

and

Press ENTER

, or Type

[3]

then

QSET

and

Press ENTER

for Quick Setup and follow the Auto Configuration Instructions.

CAUTION

When 2 VPSs are connected to the KX-TA624, the following 2 procedures should be done to
make the VPSs work correctly.

1.

Delete a mailbox in either VPS so that each extension has only ONE MAILBOX.
After Auto Configuration has been executed, an extension has a mailbox in both
VPS1 and VPS2. However each extension can have a maximum of 1 mailbox in
either VPS. To delete a mailbox, Type [D] (Delete) in the "Make (Make/Delete)"
field (see "Step 4 Creating Mailboxes" in

5.1.3

Starting the Quick Setup).

The extension should assign a Voice Mail extension from the VPS which contains
its mailbox as the destination for Call Forwarding and Voice Mail Transfer. DO
NOT assign a Voice Mail extension from the other VPS. For example, if jack 06

Table 15

Cause

Action

The PBX is not a correct type. Since the VPS is
configured to communicate with the default
PBX type (the KX-TD816/TD1232/TA1232/
TD308 under DPT Integration), this message
will always appear when connecting to another
type of PBX.

Connect a correct PBX and set
the PBX type by using Quick
Setup (see Section 5
CUSTOMIZING THE
SYSTEM).

The cabling between the PBX extension ports
and the VPS is not 4-wire or is improperly
connected.

Confirm the cabling is
connected as described in
Section 2 INSTALLATION.

The PBX is a correct type but does not have the
proper software level to support APT/DPT
Integration.

Contact National Parts Center
at 1-800-833-9626
or use Inband Integration under
hardware settings.

The PBX is not programmed properly to support
APT/DPT Integration.

Do required integration
programming as described in
this chapter.

«
...
76
77
78
79
80
...
»

Summary of Contents for KX-TVS90



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for KX-TVS90

Brand: T-Home Pages: 52

Brand: Uniden Pages: 84

Brand: Ameriphone Pages: 27

Brand: Gigaset Pages: 49

Brand: Yealink Pages: 3

Brand: AUDIOLINE Pages: 124

ON-AIR 1100 CLASSIC

Brand: BT Pages: 18

Brand: AT&T Pages: 69

Designer Bluetooth

Brand: Gecko Pages: 2

Brand: Doro Pages: 12

Brand: NEC Pages: 16

Brand: NEC Pages: 52

Brand: NEC Pages: 100

Brand: NEC Pages: 222

Brand: NEC Pages: 258

UNIVERGE UM8500

Brand: NEC Pages: 352

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands