Panasonic KX-TD6112E Features Manual Download | Manualshive

Page: 155 / 306

background image

General Features

Features Guide

155

Intelligent Call Handling — Distribution of Incoming
Outside Calls

Description

Directs an incoming outside call to a specific extension/group depending on the DDI/MSN
numbers provided by Integrated Services Digital Network (ISDN) or the calling party's
identification number (CLIP). Up to 500 CLIP numbers and 200 DDI/MSN numbers can be
stored in programme [001] System Speed Dialling and Intelligent Call Handling Number Set
(max. 32 digits).
Intelligent Call Handling (ICH) table 1 through 62 decide how an incoming outside call will
be distributed.

CLIP stands for "Calling Line Identification Presentation";
it is the ISDN version of caller ID. The CLIP number assigned in programme [001] System
Speed Dialling and Intelligent Call Handling Number Set is other party's telephone number,
but not yours.
DDI/MSN stand for "Direct Dialling Inward"/"Multiple Subscriber Numbers";
DDI/MSN numbers are your telephone numbers. You can have more than one number with an
ISDN line. Specific destinations can be assigned for each DDI/MSN number.

To assign an Intelligent Call Handling table to handle an analogue CO line call in both day and
night modes, refer to [458] Intelligent Call Handling Table for Analogue CO.

IMPORTANT
Please enable this feature as the first step. Especially, be sure to assign DDI/MSN numbers at
System Speed Dialling and Intelligent Call Handling (SSD & ICH) locations 500-699.

Note

PC programming software supports easy setup of ICH in Wizard.

Receiving Patterns

One of the following receiving patterns can be assigned to each Call Handling table.

a)

1:1 or 1:N distribution (Immediate Ringing, Delayed Ringing or No Ringing)

For a single line telephone (SLT) and a digital proprietary telephone (DPT), you can
choose from Disable (Not Receive)/No Ring (CO or DDI/CLIP button is flashing)/
Immediate/2 Rings, 4 Rings, 6 Rings, 8 Rings Delay. ([452] Extension Ringing
Assignment) Also, 1 ISDN extension number can be assigned to ring immediately.
1:1 distribution is realised by setting only 1 extension is assigned to ring and other
extension is assigned as "Disable".
1:N distribution is realised by setting 2 or more extensions to ring.

Forwarding to the Built-in Voice Message Box – Personal Message Box
This is possible if an optional card KX-TD61291 is installed and the Built-in Voice
Message (BV) feature is set up. If an SLT user or a DPT user sets call forwarding to BV

«
...
153
154
155
156
157
...
»

Summary of Contents for KX-TD6112E



















































































































































































































































































































Reviews:

No comments

Related manuals for KX-TD6112E

OpenScape CP600

Brand: Unify Pages: 32

OpenScape CP700

Brand: Unify Pages: 24

OpenScape CP200

Brand: Unify Pages: 2

OpenScape CP600

Brand: Unify Pages: 2

OpenScape Desk Phone IP 35G

Brand: Unify Pages: 130

Brand: Unify Pages: 2

Brand: Unifat Technology Pages: 6

Brand: Garmin Pages: 60

Brand: Tablee Pages: 4

MT4-16 MovieTimeS

Brand: SMART Pages: 17

Brand: Yealink Pages: 347

Brand: iTrak Pages: 6

Brand: Rath Pages: 9

MR Confon Starter f MKII+

Brand: Cambridge Research Systems Pages: 34

Brand: Scott Pages: 13

Brand: Pure Water Pages: 22

Brand: Emerson Pages: 29

Brand: Emerson Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands