Panasonic KX-TD6112E Features Manual Download | Manualshive

Page: 74 / 306

background image

General Features

74

Features Guide

Caller ID

Description

Provides a single line telephone (SLT) user with caller information, such as the caller's name
and telephone number. An optional Caller ID Sending Card with 1 CO I/F, KX-TD61283, is
required to enable this feature.

Notice:

•

This feature complies with the following ETS (European Telecommunication Standard)
specifications: ETS 300 659 Subscriber line protocol over the local loop for display
(and related) services; Part 1: On hook data transmission

•

This feature complies with only clause 6.1.1 (FSK signal transmission during ringing) and
6.1.2 b. (FSK signal transmission after RP-AS signal) in ETS 300 659. SLT extensions that
comply with either of the methods can perform Caller ID feature. There is no compliance
for the method using DT-AS signal/line reversal signal/DTMF signal nor all methods
described in Bellcore standard.

Note:

Caller ID may not be displayed according to the type of Caller ID telephone.

Conditions

•

The maximum of 20 digits of caller's telephone number can be handled by Caller ID feature.
If a telephone number is more than 20 digits, only the first 20 digits (including a line access
number if "Enable" is selected in programme [633] Caller ID Line Access Number) will be
sent to SLTs.

•

When receiving an intercom call, the calling extension number and name will be displayed.

•

When receiving an outside call from an ISDN line, the received CLIP information will be
displayed. If a name for the system speed dial number that corresponds to the CLIP number
is pre-assigned, the name is also displayed.

•

When an intercom or outside call is received by floating extension, Caller ID information
of the calling party will be displayed but not the floating extension number.

•

If an incoming call is Intelligent Call Handling 1:N or is placed to a group, Caller ID will
be sent at the same time to all SLT extensions applied to the destination.

•

A SLT connected with a digital proprietary telephone by parallelled telephone connection
can also receive Caller ID information.

•

Even if several calls are received at the same time, Caller ID will be sent to each SLT, but
ringing initiation will be delayed slightly at some SLT extensions.

•

If a call is transferred, initial information presented to the destination is an extension
number of the transferring extension. When a call is transferred by the Call Transfer,
Screened — to Extension feature, call information of the original calling party will not be
sent. When a call is transferred by the Call Transfer, Unscreened — to Extension feature,
call information of the original calling party will be displayed after the transfer initiating
extension goes on-hook.

•

Call information of the original calling party will be sent when a call is forwarded by the
Call Forwarding or Intercept Routing No Answer (IRNA).

«
...
72
73
74
75
76
...
»

Summary of Contents for KX-TD6112E



















































































































































































































































































































Reviews:

No comments

Related manuals for KX-TD6112E

Brand: Wayne Pages: 16

Aqua-Pure AP510

Brand: 3M Pages: 16

Clearspan 6731i

Brand: Aastra Pages: 3

Brand: Aastra Pages: 18

Brand: Aastra Pages: 8

Brand: Aastra Pages: 97

Brand: Aastra Pages: 7

Brand: Aastra Pages: 104

Brand: Aastra Pages: 74

Brand: Aastra Pages: 100

Brand: Yealink Pages: 2

Brand: YA Pages: 2

Brand: GE Pages: 18

Brand: JabloCom Pages: 2

Brand: Furuno Pages: 67

Brand: Panacom Pages: 16

Brand: Korg Pages: 6

Brand: Angekis Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands