![background image](http://html.mh-extra.com/html/panasonic/kx-hcm280/kx-hcm280_service-manual_277559074.webp)
Current Drive 2W1-2 Phase Excitation Micro Step Drive. It works by 1 step to the direction set by
FMDIR signal, per 1 clock of FMCLK signal given to IC1001. The motor current flows as below. In
phase A: 6V power
Q1003 6pin
Q1003 1pin
FAP signal
motor phase A
FAN
signal
IC1001 14pin
IC1001 19pin
R1003
GND, or, 6V power
Q1003 3pin
Q1003
4pin
FAN signal
motor phase A
FAP signal
IC1001 16pin
IC1001 19pin
R1003
GND In phase B: Q1006 3pin
Q1006 4pin
FBP signal
motor phase B
FBN signal
IC1001 11pin
IC1001 6pin
R1004
GND, or, 6V power
Q1006 6pin
Q1006 1pin
FBN signal
motor phase B
FBP signal
IC1001 9pin
IC1001 6pin
R1004
GND
The motor driving direction is determined by FMDIR signal.
14.2.3.4. EEPROM Block
- EEPROM (IC1009)
Power-supply voltages: 3.3V
Package: 8pin SOP
Memory Capacity: 2K x 8bit
It shall be READ/WRITE by I2CBUS signal (SCL, SDA). Memorizes
the values of LENS adjust, VIDEO adjust and VIDEO DSP install.
When the power is ON or camera unit is reset, it is READ and
installed to each system.
14.2.3.5. LED Block
A line crack and a control signal relay a Tilt board and a Video board from IP CPU by which
control of LED was mounted on the Main board, and it is inputted into the LED control circuit
mounted in the Lens board.
(As for LED, the 3 color LED is used.)
LAN_LED
PW_LED
LED COLOR
H
H
Orange
H
L
Green
L
H
Red
L
L
OFF the light
74
Summary of Contents for KX-HCM280
