Pin No.
Pin Name
I/O
Description
85
VCCQ
-
Input/Output Power Supply (+3.3V)
86
A25
O
Address Bus (Unassigned)
87
PTK4
O
Unassigned (LOW Output)
88
nRD
O
Read Signal (Low Active)
89
nWE0
O
Write Signal (Low Active)
90
nWE1
O
Write Signal (Low Active)
91
nICIORD
O
IO Read Signal (Unassigned)
92
nICIOWR
O
IO Write Signal (Unassigned)
93
RD/nWR
O
Read (High Active)/ Write (Low Active)
94
nAUDSYNC
I
Unassigned (Internal Pull-Up)
95
VSSQ
-
Input/Output Power Supply (GND)
96
nCS0
O
Flash Chip Select (Low Active)
97
VCCQ
-
Input/Output Power Supply (+3.3V)
98
nCS2
O
Chip Select (Low Active) Unassigned
99
nCS3
O
SDRAM Chip Select (Low Active)
100
nCS4
O
Unassigned
101
nCS5
O
Unassigned
102
nCS6
O
LAN and JPEG Chip Select (Low Active)
103
nCE2A
O
Unassigned
104
nCE2B
O
LAN_LED control
105
CKE5
O
CLK Enable
106
nRAS3L
O
RAS (Low Active)
107
PTJ1
O
Unassigned (LOW Output)
108
nCASLL
O
CAS (Low Active)
109
VSSQ
-
Input/Output Power Supply (GND)
110
nCASLH
O
Unassigned
111
VCCQ
-
Input/Output Power Supply (+3.3V)
112
PTJ4
O
Unassigned (LOW Output ADPCM DATA IN)
113
PTJ5
O
Unassigned (LOW Output ADPCM EX CLK)
114
nDACK0
O
DMA Transfer ACK (Low Active)
115
nDACK1
O
Tilt Motor Control (PH2)
116
PTE6
O
Tilt Motor Control (PH1)
117
PTE3
O
Boot Control 2
118
nRAS3U
O
Unassigned
119
PTE1
O
Boot Control 1
120
TDO
I
Unassigned (Internal Pull-Up)
121
nBACK
O
Unassigned
122
nBREQ
I
Unassigned (External Pull-Up)
123
nWAIT
I
Hardware WAIT Request (Low Active)
124
nRESETM
I
Unassigned (External Pull-Up)
125
PTH5
I
Unassigned (External Pull-Down)
126
PTG7
I
Unassigned (External Pull-Up)
79
Summary of Contents for KX-HCM280
