Pin
No.
Pin Name
I/O
Description
27
28
29
30
MODE[0]
MODE[1]
MODE[2]
MODE[3]
I
Input/Output Change Input when outside setting mode (Internal
resistance Pull-Down)
Inside/Outside terminals change Register MRA[0].
The Default of Register MRA[0] is External resistance Mode.
MODE[3:2] Output Mode Selection
00: ITU-R BT.656(Processed by 8bit YCbCr SAV, EAV and blank)
01: 8bit (YCbCr)
10: 16bit (YCbCR) (ITU-RBT.601)
11: 24bit RGB
MODE[1] Input Mode Selection
0: NTSC/1:PAL
When the Setting of Register MRA[7] is NTSC/PAL Auto recognize and
Input ITU-T.601 signal, it is invalidated.
MODE[0] Input Mode Selection
0: ITU-RBT.601/1: Square Pixel
NTSC 4 Fsc setting is possible only register setting is MRA[3:1].
31
SCAN
I
Not use. Open or hold "0" (Internal resistance Pull-Down)
32
TEST[2]
I
Not use. Open or hold "0" (Internal resistance Pull-Down)
33
TEST[1]
I
Not use. Open or hold "0" (Internal resistance Pull-Down)
34
TEST[0]
I
Not use. Open or hold "0" (Internal resistance Pull-Down)
35
SLEEP
I
0: Normal / 1: Sleep
36
RESET_L
I
Reset Input (Active "L")
Please Reset after Power-on supply
37
DVDD
-
Digital part Power Supply
38
DGND
-
Digital part Ground
39
SCL
I
I2C Bus clock Input
40
SDA
I/O
I2C Bus data Input / Output terminal
41
PLLSEL
I
Not use. Open or hold "0" internal resistance Pull-Down)
42
CLKSEL
I
Clock selection Input terminal
0: Double speed Input Mode / 1: Normal speed Input Mode
Input Double frequency to System Clock to use Double speed Input
Mode
43~50
B[7~0]
O
Data Output B[7]: MSB, B[0]: LSB
RGB Output Mode time: B 8 bit Data Output
It is Hi-z besides RGB Output Mode.
Output Mode is set on the 27-28 pin or Register MRA[7:6]
51
DGND
-
Digital part Ground
52
DVDD
-
Digital part Power Supply
90
Summary of Contents for KX-HCM280
