Max bit rate(per client)
[512kbps, 768kbps, 1024kbps, 1536kbps, 2048kbps,
3072kbps, 4096kbps, 6144kbps, 8192kbps, 10240kbps,
12288kbps, 14336kbps, 16384kbps, 20480kbps, 24576kbps]
Specify the H.264 bit rate per client.
When [Transmission priority] is set to [Best effort], specify the
maximum and minimum bit rate.
Factory settings:
H.264(1): 14336kbps
H.264(2): 8192kbps
H.264(3): 4096kbps
H.264(4): 4096kbps
<NOTE>
• The setting range depends on the resolution.
Image quality [Motion priority, Image quality priority]
Select the image quality for H.264 images.
Motion priority
Mode giving priority to image motion.
Image quality
priority
Mode giving priority to image quality.
Factory settings:
Motion priority
<NOTE>
• This setting is only enabled when [Transmission priority] is set to
[Constant bit rate] or [Best effort].
Transmission type [Unicast port(AUTO), Unicast
port(MANUAL), Multicast]
Select the transmission format for H.264 images.
Unicast
port(AUTO)
Up to 14 users can access a single camera at the
same time.
[Unicast port(Image)] and [Unicast port(Audio)] will be
configured automatically when images and audio are
sent from the camera.
We recommend selecting the [Unicast port(MANUAL)]
setting when the port number transmitting the H.264
images does not need to be fixed (e.g., during use
within a network).
Unicast
port(MANUAL)
Up to 14 users can access a single camera at the
same time.
[Unicast port(Image)] and [Unicast port(Audio)] must
be configured manually when images and audio are
sent from the camera.
When transmitting H.264 images via the Internet,
configure a fixed transmission port for the
broadband router (hereafter referred to as “router”)
(→ page 113). For details, refer to the operating
instructions for the router.
Multicast
An unlimited number of users can access a single
camera at the same time.
When transmitting H.264 images via multicast, enter
the [Multicast address], [Multicast port], and [Multicast
TTL/HOPLimit].
Factory settings:
Unicast port(AUTO)
<NOTE>
• For details on the maximum number for simultaneous access, see
page 74.
Unicast port(Image) [1024 to 50000]
Enter the unicast port number (used when sending images from the
unit).
Only even numbers can be specified.
The port number cannot be set to 10670.
Factory settings:
H.264(1): 32004
H.264(2): 32014
H.264(3): 32024
H.264(4): 32034
Unicast port(Audio) [1024 to 50000]
Only even numbers can be specified.
The port number cannot be set to 10670.
Factory settings:
H.264(1): 33004
H.264(2): 33014
H.264(3): 33024
H.264(4): 33034
<NOTE>
• The unicast port number must be configured when [Transmission
type] is set to [Unicast port(MANUAL)].
Multicast address
[IPv4: 224.0.0.0 to 239.255.255.255
IPv6: Multicast address starting with FF]
Enter the multicast IP address.
Images and audio will be sent to the specified IP address.
Factory settings:
H.264(1): 239.192.0.20
H.264(2): 239.192.0.21
H.264(3): 239.192.0.22
H.264(4): 239.192.0.23
<NOTE>
• Verify usable multicast IP addresses before entering this setting.
Multicast port [1024 to 50000]
Enter the multicast port number (used when sending images from the
unit).
Only even numbers can be specified.
The port number cannot be set to 10670.
Factory settings:
37004
<NOTE>
• When sending audio from the unit, a port number with “1000” added
to the multicast port number will be used.
Multicast TTL/HOPLimit [1 to 254]
Enter the TTL/HOPLimit value for multicast.
Factory settings:
16
<NOTE>
• When transmitting H.264 images via the Internet, transmitted
images may not appear depending on proxy server settings, firewall
settings, etc. In such cases, consult your network administrator.
• When displaying multicast images on a personal computer with
multiple LAN cards installed, disable the LAN cards that are not
used for reception.
92
93
Web screen configurations (continued)
Summary of Contents for AW-HE145WP
Page 102: ...z zPicture 102 Web screen configurations continued ...
Page 155: ...155 MEMO ...
