Packard Bell dot s Series Service Manual Download Page 149

Page: 149 / 182

Chapter 4

139

Thermal Unit Failure

If the

Thermal

Unit

fails, perform the following actions one at a time to correct the problem. Do not replace a

non-defective FRUs:

External Mouse Failure

If an external

Mouse

fails, perform the following actions one at a time to correct the problem.

Try an alternative mouse.

If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See
the mouse user manual.

If the mouse uses a USB connection, try an alternate USB port.

Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure.

Restart the computer.

Remove any recently added hardware and associated software.

Remove any recently added software and reboot.

Restore system and file settings from a known good date using

System

Restore

If the issue is not fixed, repeat the preceding steps and select an earlier time and date.

Run the Event Viewer to check the events log for errors. For more information see Windows Help and
Support.

10.

Roll back the mouse driver to the previous version if updated recently.

11.

Remove and reinstall the mouse driver.

12.

Check the Device Manager to determine that:

•

The device is properly installed. There are no red Xs or yellow exclamation marks.

•

There are no device conflicts.

•

No hardware is listed under Other Devices.

START

Fan power

cable well

connected?

Connect it well

Fan OK?

Replace fan

Seat it well

Replace M/B

CPU

Heat sink well

seated?

Downloaded from LpManual.com Manuals

Summary of Contents for dot s Series























































































































































































Search results

Summary of Contents for dot s Series

Reviews:

Related manuals for dot s Series

Brands by name

Popular brands

Packard Bell dot s Series, Service Manual

Search results

Summary of Contents for dot s Series

Reviews:

Related manuals for dot s Series

Brands by name

Popular brands