Packard Bell dot s Series Service Manual Download Page 145

Page: 145 / 182

Chapter 4

135

Reboot the computer.

Navigate to

Start

Control

Panel

System

and

Maintenance

System

Device

Manager

. Check

the Device Manager to determine that:

•

The device is properly installed.

•

There are no red Xs or yellow exclamation marks.

•

There are no device conflicts.

•

No hardware is listed under Other Devices.

Roll back the audio driver to the previous version, if updated recently.

Remove and reinstall the audio driver.

Ensure that all volume controls are set mid range:

Click the volume icon on the taskbar and drag the slider to 50. Ensure that the volume is not muted.

Click Mixer to verify that other audio applications are set to 50 and not muted.

Navigate to

Start

Control

Panel

Hardware

and

Sound

. Ensure that Speakers are selected

as the default audio device (green check mark).

NOTE:

If Speakers does not show, right-click on the

Playback

tab and select

Show

Disabled

Devices

(clear by default).

Select Speakers and click

Configure

to start

Speaker

Setup

. Follow the onscreen prompts to configure

the speakers.

Remove and recently installed hardware or software.

Restore system and file settings from a known good date using

System

Restore

If the issue is not fixed, repeat the preceding steps and select an earlier time and date.

10.

Reinstall the Operating System.

11.

If the Issue is still not resolved, see “Online Support Information” on page 167.

Downloaded from LpManual.com Manuals

Summary of Contents for dot s Series























































































































































































Search results

Summary of Contents for dot s Series

Reviews:

Related manuals for dot s Series

Brands by name

Popular brands

Packard Bell dot s Series, Service Manual

Search results

Summary of Contents for dot s Series

Reviews:

Related manuals for dot s Series

Brands by name

Popular brands