Packard Bell dot s Series Service Manual Download Page 139

Page: 139 / 182

Chapter 4

129

Troubleshooting

Common Problems

Use the following procedure as a guide for computer problems.

NOTE:

The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or

modified options can give false errors and invalid system responses.

Obtain the failing symptoms in as much detail as possible.

Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.

Use the following table with the verified symptom to determine which page to go to.

If the Issue is still not resolved, see “Online Support Information” on page 167.

Symptoms (Verified)

Go To

Power On Issue

Page 130

No Display Issue

Page 131

LCD Failure

Page 133

Internal Keyboard Failure

Page 133

TouchPad Failure

Page 134

Internal Speaker Failure

Page 134

Internal Microphone Failure

Page 136

WLAN Failure

Page 138

Thermal Unit Failure

Page 139

Other Functions Failure

Page 140

Intermittent Failures

Page 141

Undermined Failures

Page 141

Chapter 4

Downloaded from LpManual.com Manuals

Summary of Contents for dot s Series























































































































































































Search results

Summary of Contents for dot s Series

Reviews:

Related manuals for dot s Series

Brands by name

Popular brands

Packard Bell dot s Series, Service Manual

Search results

Summary of Contents for dot s Series

Reviews:

Related manuals for dot s Series

Brands by name

Popular brands