3
DA400R
AIR COMPRESSOR (1/6 H.P.)
1/6 H.P. Piston Compressor with Auto shutoff. Compressor shuts off when airbrush is
not in use. Operating pressure 30 - 50 PSI depending on airbrush being used, delivers
up to 55 psi.. 110-120VAC, 1 Ph, 60 Hz, 42L/Min. (1.48CFM), 1720 rpm. With
R-75
Regulator & Moisture Trap included.
Shipping Weight: 13 lbs. 9 oz. (6.16 kgs)
D500 AIR COMPRESSOR (1/8 H.P.) (ETL Listed)
Economical and suitable for all airbrushes spraying properly thinned fluids. It is capable
of delivering up to 35 P.S.I. operating pressure depending on airbrush being used. The
Paasche
D500
is an oilless piston compressor. It operates on 110-120 Volt, 1 phase,
60Hz, and delivers .4 C.F.M. @ 20 P.S.I.
Shipping Weight: 8 lbs. 3 oz. (3.7kg)
D500SR
AIR COMPRESSOR (1/8 H.P.), ETL Listed
with Switch & R-75
Regulator
Economical and suitable for all airbrushes spraying properly thinned fluids. Maximum
20 - 35 P.S.I. operating pressure depending on airbrush being used. The Paasche
D500SR
is an oilless piston unit and comes with the
R-75
Regulator/Filter with gauge.
It operates on 110-120 Volt, 1 phase, 60Hz, and delivers .4 C.F.M. @ 20 P.S.I.
R75
Regulator will regulate up to 35 P.S.I. depending on usage (intermittent or constant)
and size of airbrush being used.
Shipping Weight: 8 lbs. 12 oz. (3.97kg)
D220R AIR COMPRESSOR (1/6 H.P.), with Switch & R-75 Regulator
Economical and suitable for all airbrushes spraying properly thinned fluids. It is capable
of delivering 30 - 45 P.S.I. operating pressure depending on airbrush being used. The
Paasche
D220R
is an oilless diaphragm unit and comes with the
R-75
Regulator/Filter
with gauge. It operates on 110-120 Volt, 1 phase, 60Hz, and delivers .7 C.F.M. @ 20
P.S.I.
R75
Regulator will regulate up to 45 P.S.I. depending on usage (intermittent or
constant) and size of airbrush being used.
Shipping Weight: 11 lbs. (5kg)
VSR90#1 ACCESSORIES
NO.
PART
DESCRIPTION
9.
A-34
Airbrush Hanger
10.
V-62
Airbrush Wrench
12.
MT
Moisture Trap (Do-It-Yourself Installation)
13.
HP-1/8
PVC Red Plastic Airhose w/cplgs.
14.
A-1/8
Braided Airhose w/Couplings
15.
AC-20
1/8"-1/4"-40 Coupling (To Airbrush)
16.
AC-1/8
-1/4" Coupling (To Compressor)
ACCESSORIES - not shown
PART NO.
DESCRIPTION
R-75
Reg. & Filter w/Gauge
HSSB-22-16
Hobby-Shop Spray Booth
A-194
Deluxe Airbrush Hanger
Printed in the USA
2. Dirty tip or needle - Remove and clean
3. Tip not centered in aircap - Remove head and clean airbrush seat and tip seat then reassemble. Use wrench for aircap body
Jammed trigger or poor trigger motion:
1. Adjust Needle Adj. Sleeve - Screw or unscrew the sleeve to lessen or increase tension on trigger motion
2. Paint leaking to trigger area - Remove guts of airbrush and slightly tighten packing or replace if needed
3. Lubricate needle and trigger - Apply lubricant to needle shaft and trigger slot area
9
10
