background image

Power tools that are no longer usable should not be 

disposed of with household waste but in an environmentally 

friendly way. Please recycle where facilities exist. Check 

with your local council authority for recycling advice.

Recycling packaging reduces the need for landfill and raw 

materials. Reuse of recycled material decreases pollution in 

the environment. Please recycle packaging where facilities 

exist. Check with your local council authority for recycling 

advice.

6. APPLIANCE CARE

MAINTENANCE

DESCRIPTION OF SYMBOLS

CARING FOR THE ENVIRONMENT

SPARE PARTS

Cleaning

1.  We recommend that you clean the appliance immediately after you 

use it.

2.  Keep the safety devices free of dirt and dust as much as possible. 

Wipe the equipment with a clean cloth.

3.  Clean the appliance regularly with a damp cloth and some soft 

soap. Do not use cleaning agents or solvents; these may be 

aggressive to the plastic parts in the appliance. Ensure that no 

water can get into the interior of the appliance.

4.  You must disconnect the hose and any spraying tools from the 

compressor before cleaning. Do not clean the compressor with 

water, solvents or the like.

Storage

Pull the mains plug out of the socket and ventilate the appliance and 

all connected pneumatic tools. Switch off the compressor and make 

sure that it is secured in such a way that it cannot be started up again 

by any unauthorised person. 

Store the compressor only in a dry location which is not accessible to 

unauthorised persons.

Supply Cords

If the replacement of the supply cord is necessary, this has to be done 

by a certified electrician in order to avoid a safety hazard.

Note: 

Ozito Industries will not be responsible for any damage or 

injuries caused by the repair of the tool by an unauthorised person or 

by mishandling of the tool.

WARNING! 

BEFORE CLEANING YOUR AIR 

COMPRESSOR OR CARRYING OUT ANY 

MAINTENANCE PROCEDURE, MAKE SURE THAT IT 

IS DISCONNECTED FROM THE POWER SUPPLY TO 

PREVENT ACCIDENTAL STARTING.

  

V

 

    

Volts

 

   

Hz

 

    

Hertz

  

~

 

    

Alternating current

 

 

W

 

    

Watts

 

    

Revolutions or 

 

    reciprocation per minute

     

 

 

 

 

n

o       

No load speed

Warning

Wear hearing protection

Read instruction manual

Beware of electrical voltage

Beware of hot parts.

96

Sound power level

Pressure rating

bar

L

/min

Litres

Electrical Emissions

Conformity (EMC)

Ingress protection from water

lP20

Warning! The equipment is

remote-controlled and may start-up

 without warning.

Spare parts can be ordered from the Special Orders Desk 

at your local Bunnings Warehouse. 
For further information, or any parts not listed here, visit 
www.ozito.com.au or contact Ozito Customer Service: 
Australia 1800 069 486 
New Zealand 0508 069 486 
E-mail: [email protected]

Summary of Contents for ACP-5020K

















Reviews: