background image

OZ-50PK

4. INFLATING

3. BLOW GUN

Inflating Tyres

1.  Follow the instructions in 

1. Assembly (Connecting 

to the Air Compressor)

 to 

connect the Air Chuck to the 

compressor.

2.  Follow the instructions for operating your compressor. Check that 

the compressor is set to the correct air pressure for tyre you are 

trying to inflate.

3.  Press the head of the Air 

Chuck firmly into the valve 

stem to form a good seal. Air 

flowing into the tyre should be 

heard. Once there is a notable 

decrease in sound, or the 

tyre feels firm, remove the Air 

Chuck. 

4.  Press the Tyre Pressure 

Gauge firmly onto the valve 

stem to check the tyre 

pressure. If the desired 

pressure has not been 

reached, repeat step 3.

WARNING! 

AVOID INFLATING OBJECTS ABOVE THE 

RECOMMENDED INFLATION PRESSURE. THIS MAY 

LEAD TO DAMAGE AND/OR INJURIES.

Spraying Compressed Air

The Blow Gun can be used with the High Pressure Nozzle to direct 

jets of compressed air at work pieces/surfaces.

1.  Attach the High Pressure 

Nozzle to the nozzle of the 

Blow Gun.

2. Connect the blow gun via the Nitto Connectors to the Air Hose.

3.  Squeeze the Trigger to release compressed air.

Note:

 Varying the amount of pressure on the Trigger of the Blow Gun 

allows you to control the amount of compressed air released through 

the nozzle.

Inflation Nozzles

Additional nozzles have also been provided for inflating objects 

with the blow gun. These are suited for the different types of valves 

commonly found on inflatable objects.

The Needle Nozzle is used for 

footballs, basketballs, soccer 

balls, etc. 

The silver Safety Adaptor will 

need to be used to connect this 

to the blow gun.

The Tapered Nozzle and Rubber 

Nozzle are used for rubber 

dinghies, inflatable swimming 

pools and air beds. 

The silver Safety Adaptor will 

need to be used with the Rubber 

Nozzle.

WARNING! 

NEVER POINT THE NOZZLE OF AN 

ACCESSORY TOWARDS ANY PART OF YOUR BODY 

OR TOWARDS ANOTHER PERSON OR ANIMAL.

WARNING! 

OPERATOR IS ADVISED TO WEAR EYE 

PROTECTION WHEN USING THE AIR GUN. TAKE 

CARE NOT TO BLOW DIRT OR OTHER LOOSE 

PARTICLES TOWARDS YOURSELF OR OTHER 

PERSONS.

Summary of Contents for ACP-5020K

















Reviews: