Owon SDS-E Series User Manual Download Page 63

Page: 63 / 106

5.Advanced User Guidebook

contains two kinds: Internal and External.
When the storage medium is Internal, Wave Record contains four modes:

OFF

Record

Playback

and

Storage

When storage medium is External

（

See P61 Wave Record Menu of External Storage

）

Wave Record contains two modes:

OFF, Record.

Record

: To record wave according to the interval until it reaches the end frame set.

Record menu (Internal Storage) shows as follows:

Menu

Setting

Instruction

Mode

OFF

Record

Playback

Storage

Close wave record function
Set record menu
Set playback menu
Set storage menu

Record mode

FrameSet

End frame Turn the

knob to select the number of frames to

record (1 - 1000)

Interval

Turn the

knob to select the interval between

recorded frames (1 ms - 1000 s)

Refresh

OFF

Refresh wave during recording
Stop refreshing

Operate

Play
Stop

Begin to record
Stop recording

Note

Both of the waveforms of Channel 1 and Channel 2 will be recorded. If a Channel is
turned off while recording, the waveform of the channel is invalid in the playback mode.

Figure 5-52 Wave Record

Playback

: Play back the wave recorded or saved.

Playback menu shows as follows:

Menu

Setting

Instruction

Summary of Contents for SDS-E Series











































































































Search results

Summary of Contents for SDS-E Series

Reviews:

Related manuals for SDS-E Series

Brands by name

Popular brands

Owon SDS-E Series, User Manual

Search results

Summary of Contents for SDS-E Series

Reviews:

Related manuals for SDS-E Series

Brands by name

Popular brands