Owon SDS-E Series User Manual Download Page 66

Page: 66 / 106

5.Advanced User Guidebook

Figure 5-55: Wave Record Menu of External Storage

Record menu (External Storage) shows as follows:

Menu

Setting

Instruction

Mode

OFF

Record

Close wave record function
Set record menu

Record mode

FrameSet

End frame Turn the

knob to select the number of frames to

record (1 - 1000)

Interval

Turn the

knob to select the interval between

recorded frames (1ms - 1000s)

Infinity

Record infinitely until the storage medium is full

Refresh

OFF

Refresh wave during recording
Stop refreshing

Operate

Play
Stop

Begin to record
Stop recording

Note

Both of the waveforms of Channel 1 and Channel 2 will be recorded. If a Channel is
turned off while recording, the waveform of the channel is invalid in the playback mode.

Summary of Contents for SDS-E Series











































































































Search results

Summary of Contents for SDS-E Series

Reviews:

Related manuals for SDS-E Series

Brands by name

Popular brands

Owon SDS-E Series, User Manual

Search results

Summary of Contents for SDS-E Series

Reviews:

Related manuals for SDS-E Series

Brands by name

Popular brands