Owon SDS-E Series User Manual Download Page 53

Page: 53 / 106

5.Advanced User Guidebook

Figure 5-34

XY Display Mode

Trig Freq

It is a 6-digit trig freq. The trig freq can measure frequencies from 2Hz to the full
bandwidth. Only if the measured channel has triggering signal and in

Edge

mode, it can

measure frequency correctly. In the

Single

trigger mode, it is a one channel trig freq and it

can only measure the frequency of the triggering channel. In the

ALT

trigger mode, it is a

two channel trig freq and it can measure the frequency of two channels. The trig freq is
displayed at the right bottom of the screen.

To turn the trig freq on or off:

Press the

Display

button.

In the

Display

menu, press the

button to toggle between the trig freq display

OFF

VGA Output (VGA port is optional)

The VGA port could be connected to a computer monitor. The image of the oscilloscope
can be clearly displayed on the monitor.

To set the VGA Output:
1.

Press the

Display

button.

In the

Display

menu, press the

button to toggle between

OFF

How to Save and Recall a Waveform

Press the

Save

button, you can save the waveforms, settings or screen images. The menu

displayed in the screen is shown as

Figure 5-35

Summary of Contents for SDS-E Series











































































































Search results

Summary of Contents for SDS-E Series

Reviews:

Related manuals for SDS-E Series

Brands by name

Popular brands

Owon SDS-E Series, User Manual

Search results

Summary of Contents for SDS-E Series

Reviews:

Related manuals for SDS-E Series

Brands by name

Popular brands