Owon SDS-E Series User Manual Download Page 83 | Manualshive

Page: 83 / 106

background image

5.Advanced User Guidebook

78

Figure 5-78 Autoscale Horizontal-Vertical multi-period waveforms

Note

:

1.

Entering into Autoscale function and the symbol

○

A

will be

flickering on the top

left of the screen every 0.5 second.

2.

In the mode of Autoscale, the oscilloscope can self-estimate "Trigger Type" (Single,
and Alternate) and "Mode" (Edge, Video). At this point, the trigger menu is not
available.

3.

At the mode of XY and STOP status, pressing

Autoset

to enter into Autoscale, DSO

switches to YT mode and AUTO triggering.

4.

At the mode of Autoscale, DSO is always set as DC coupling with AUTO triggering.
In this case, making Triggering or Coupling settings have no effect.

5.

At the mode of Autoscale, if adjust the vertical position, voltage division, trigger level
or time scale of CH1 or CH2, the oscilloscope will turn off Autoscale function. To
back to Autoscale, press

Autoset

.

6.

Turn off the submenu at the Autoscale menu, the Autoscale is off and turn on the
submenu still enters into the function.

7.

When video triggering, the horizontal time scale is 50us. If one channel is showing
edge signal, the other channel is showing video one, the time scale refers to 50us as
video one as standard.

8.

While the Autoscale is working, settings below will be made forcibly:
(1) The DSO will switch from non-main time base to main time base status.
(2) The DSO will switch to Peak detection mode if it is in Average mode.

How to Use Built-in Help

1.

Press

Help

button, the catalog will display in the screen.

2.

Press

H1

or

H2

to choose help topic, or just turn the

M

knob to choose.

3.

Press

H3

to view the details about the topic, or just press the M knob.

«
...
81
82
83
84
85
...
»

Summary of Contents for SDS-E Series











































































































Reviews:

No comments

Related manuals for SDS-E Series

Brand: GE Pages: 2

Druck DPI 620 Genii

Brand: GE Pages: 154

Arize Element Top Light

Brand: GE Pages: 2

Brand: Datex-Ohmeda Pages: 104

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 166

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 340

WJHD309 - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 7

WJ-ND300 Administrator Console

Brand: Panasonic Pages: 24

Brand: ACE INSTRUMENTS Pages: 15

Brand: Wave Fitness Pages: 15

Brand: B&G Pages: 3

Brand: Rapid Technic Pages: 152

Brand: Datavideo Pages: 48

Brand: Datavideo Pages: 34

Brand: Datavideo Pages: 3

Brand: Datavideo Pages: 34

Brand: Datavideo Pages: 8

Brand: Datavideo Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands