Owon SDS-E Series User Manual Download Page 38

Page: 38 / 106

5.Advanced User Guidebook

How to Set the Horizontal System

The

HORIZONTAL CONTROLS

includes the

HORIZ MENU

button and such

knobs as

HORIZONTAL POSITION

and

SEC/DIV

HORIZONTAL POSITION

knob: this knob is used to adjust the horizontal

positions of all channels (include those obtained from the mathematical
manipulation), the analytic resolution of which changes with the time base.

SEC/DIV

knob: it is used to set the horizontal scale factor for setting the main

time base or the window.

HORIZ MENU

button: with this button pushed down, the screen shows the

operating menu (see

Figure 5-14

Figure 5-14

Time Base Mode Menu

The description of the

Horizontal Menu

is as follows:

Function Menu

Description

Main (Main Time Base)

The setting of the horizontal main time base is
used to display the waveform.

Set (Set Window)

A window area is defined by two cursors. This
function is not available at FFT mode.

Zoom (Zoom Window)

The defined window area for display is
expanded to the full screen.

Main Time Base

Press the

menu selection button and choose

Main.

In this case, the

HORIZONTAL POSITION

and

SEC/DIV

knobs are used to adjust the main

window. The display in the screen is shown as

Figure 5-15

Summary of Contents for SDS-E Series











































































































Search results

Summary of Contents for SDS-E Series

Reviews:

Related manuals for SDS-E Series

Brands by name

Popular brands

Owon SDS-E Series, User Manual

Search results

Summary of Contents for SDS-E Series

Reviews:

Related manuals for SDS-E Series

Brands by name

Popular brands