Owon SDS-E Series User Manual Download Page 72

Page: 72 / 106

5.Advanced User Guidebook

Save rule:

Press

button, then

button to save the rules, which could be called up

at once when need, press

button to call up the rule saved.

Figure 5-64 Pass/Fail test

Note:

When Pass/Fail is ON, if XY or FFT is ready to run, then Pass/Fail will be closed;

under the mode of XY or FFT, Pass/Fail is unable.

Under the mode of Factory, Auto Scale and Auto Set, Pass/Fail will be closed.

When no save setting left in the rule save, tip will be given to show "NO RULE

SAVED".

Under the status of stop, data comparing will stop, and when it goes on running, the

number of Pass/Fail will increase from the former number, not from zero.

When the waveform playback mode is on, Pass/Fail is used to test the played-back

waveform specially.

●

Output

Press the

Utility

button and turn the

to select the

Output

to go to the following menu.

Figure 5-65 Output menu

The description of

Output menu

is shown as the follows:

Function

Menu

Setting

Description

Type

Trig level

Pass/fail

Output trig signal synchronously
Output High Level when Pass , and Low Level when Fail

Summary of Contents for SDS-E Series











































































































Search results

Summary of Contents for SDS-E Series

Reviews:

Related manuals for SDS-E Series

Brands by name

Popular brands

Owon SDS-E Series, User Manual

Search results

Summary of Contents for SDS-E Series

Reviews:

Related manuals for SDS-E Series

Brands by name

Popular brands