ORTEC Easy-MCS Hardware User Manual Download Page 120 | Manualshive

Page: 120 / 132

background image

Easy-MCS

™

Multichannel Scaler and MCS-32 (A73-B32) Software

931054C / 1213

110

SET_LLSCA 1.2
SET_PASS_LENGTH 1000
SET_PASS_PRES 0
SET_ULSCA 6.5

RESET

Resets the MCS to the state just after power is applied.

SET_DISCRIMINATOR voltage

Sets the input discriminator threshold to the specified voltage. Voltage has a maximum value
of +3.0 and a minimum value of

!

1.6. Legal values b3.0 and

!

1.6 occur nominally

every 0.0015256 volts. When an invalid value is specified, the value is rounded off to the
closest legal value and a warning message is returned. See also SHOW_DISCRIMINATOR.

SET_DISCRIMINATOR_LEADING

Makes the input discriminator leading (rising) edge sensitive. After this command is issued,
the counters will increment when the input crosses the threshold with a positive slope. See
also SHOW_DISC_EDGE and SET_DISCRIMINATOR_TRAILING.

SET_DISCRIMINATOR_TRAILING

Makes the input discriminator trailing (falling) edge sensitive. After this command is issued,
the counters will increment when the input crosses the threshold with a negative slope. See
also SHOW_DISC_EDGE and SET_DISCRIMINATOR_LEADING.

SET_DWELL dwell

Sets the dwell time to the specified value. Dwell is in units of seconds and exponential nota-
tion is permitted. Dwell has a maximum value of 65535 and a minimum value of 5×10

!9

.

Legal values between the minimum and maximum values may be determined by using the
VERIFY_DWELL command. The value can then be set with SET_DWELL. If an invalid
value is specified, the value is rounded to the closest legal value and a warning message is
returned. See also SHOW_DWELL, ENAB_DWELL_EXT and DISA_DWELL_EXT.

SET_DWELL_ETHLD voltage

Sets the external dwell threshold. The value of voltage can be a floating-point number
between –1.6 V and +3.0 V. Legal values occur between these limits nominally every
0.0015256 volts. When an invalid value is specified, the value is rounded off to the closest
legal value. See also SHOW_DWELL_ETHLD.

SET_INPED number

Sets the input impedance. Number has only 2 valid values, zero and 1. Zero sets the input
impedance to 50

Ω

; 1 sets the input impedance to 1 k

Ω

. See also SHOW_INPED.

«
...
118
119
120
121
122
...
»

Summary of Contents for Easy-MCS





































































































































Reviews:

No comments

Related manuals for Easy-MCS

Brand: ultimatte Pages: 125

Brand: 3One data Pages: 9

Brand: YOKOGAWA Pages: 58

Brand: APsystems Pages: 22

Varispeed CIMR-G7A

Brand: YASKAWA Pages: 459

VARIOMAT 2 11MM

Brand: Calpeda Pages: 64

Brand: LAN Power Pages: 2

Brand: Aquatic Pages: 5

PowerClean Salt Econ

Brand: CMP Pages: 24

Brand: Energie Pages: 36

Brand: CEL-MAR Pages: 28

Brand: Xnexus Pages: 20

Brand: B PLUS TV Pages: 10

Brand: ICT Pages: 2

Brand: Defort Pages: 40

Brand: SIIG Pages: 12

Brand: TRUlink Pages: 15

Brand: Tesla Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands