Orientalmotor CSK243-ATA Operating Manual Download Page 39

Page: 39 / 48

7 Setting

−

Setting method for

CSD2140T

CSD2145T

•

Connecting an ammeter

Connect the driver, motor and DC ammeter.

Motor leads color

2-phase stepping motor

Driver TB2

RED

BLUE

GREEN

BLACK

YELLOW

WHITE

Red

Blue

Green

Black

Yellow

White

•

Adjusting the motor operating current

Set the jumper socket for the step angle switch
(FULL/HALF) to FULL.

Set the jumper socket for automatic current
cutback function (C.C./A.C.D.) to C.C.

Turn on the power supply.

Wait until the motor reaches its operating current.

Using an insulated screwdriver, manipulate the
potentiometer for adjusting the motor operating
current (RUN VR).

Be sure to adjust the current to the motor’s rated
current or below.
The sum of two DC ammeter readings indicates the
current per motor phase.

Turn off the power supply.

RUN VR

Set the jumper socket for automatic current
cutback function (C.C./A.C.D.) to A.C.D. again.

This completes the adjustment of the motor operating
current.

Summary of Contents for CSK243-ATA

















































Search results

Summary of Contents for CSK243-ATA

Reviews:

Related manuals for CSK243-ATA

Brands by name

Popular brands

Orientalmotor CSK243-ATA, Operating Manual

Search results

Summary of Contents for CSK243-ATA

Reviews:

Related manuals for CSK243-ATA

Brands by name

Popular brands