Orientalmotor CSK243-ATA Operating Manual Download Page 36

Page: 36 / 48

7 Setting

−

Setting method for

CSD2109-T

CSD2112-T

CSD2120-T

An ammeter or tester is needed to set the motor current. Note that a tester is required
only for the

CSD2109-T

CSD2112-T

and

CSD2120-T

•

Connecting an ammeter or tester

Connecting an ammeter:

Connect the driver, motor and DC ammeter.

Motor leads color

2-phase stepping motor

Driver TB2

Yellow

White

Black

Green

Red

Blue

YELLOW

WHITE

BLACK

GREEN

RED

BLUE

Connecting a tester:

Connect the driver and motor.

Motor leads color

2-phase stepping motor

Driver TB2

YELLOW

WHITE

BLACK

GREEN

RED

BLUE

Yellow

White

Black

Green

Red

Blue

Insert the tester probes [approx. 2.1 mm (0.08 in.) in diameter] into the motor
current check terminals (C.C.+, C.C.

−

). Set the tester to the voltage measuring

range.

C.C.+

C.C.-

Summary of Contents for CSK243-ATA

















































Search results

Summary of Contents for CSK243-ATA

Reviews:

Related manuals for CSK243-ATA

Brands by name

Popular brands

Orientalmotor CSK243-ATA, Operating Manual

Search results

Summary of Contents for CSK243-ATA

Reviews:

Related manuals for CSK243-ATA

Brands by name

Popular brands