Orientalmotor CSK243-ATA Operating Manual Download Page 20 | Manualshive

Page: 20 / 48

background image

5 Installation

−

20

−

CSD2140T

,

CSD2145T

Mount the driver to the mounting plate using No.4-40 UNC screws.

•

Horizontal installation

Mounting
plate

No.4-40 UNC
screw

•

Vertical installation

Mounting
plate

No.4-40 UNC
screw

5.6 Installing and wiring in compliance with EMC

Directive

Effective measures must be taken against the EMI that the

CSK

series may give to

adjacent control-system equipment, as well as the EMS of the

CSK

series itself, in

order to prevent a serious functional impediment in the machinery. The use of the
following installation and wiring methods will enable the

CSK

series to be

compliant with the EMC Directive (the aforementioned compliance standards).
The compliance of the final machinery with the EMC Directive will depend on such
factors as the configuration, wiring, layout and risk involved in the control-system
equipment and electrical parts. It therefore must be verified through EMC measures
by the customer of the machinery.

Applicable standards

EMI Emission

Tests

Radiated Emission Test

EN 61000-6-4
EN 55011

EMS Immunity

Tests

Radiation Field Immunity Test
Fast Transient / Burst Immunity Test
Conductive Noise Immunity Test

EN 61000-6-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-6

•

About power supply

The

CSK

series products are of the DC power supply input specification. Use a DC

power supply that is optimally compliant with the EMC Directive.

«
...
18
19
20
21
22
...
»

Summary of Contents for CSK243-ATA

















































Reviews:

No comments

Related manuals for CSK243-ATA

Brand: Hacker Pages: 8

Brand: Fagor Pages: 174

Brand: Daihatsu Pages: 294

Brand: BAFANG Pages: 12

Brand: WÄRTSILÄ Pages: 232

Brand: Kohler Pages: 116

Brand: SEW-Eurodrive Pages: 88

Brand: IEF Werner Pages: 38

Brand: Amico Pages: 47

Brand: Stark Pages: 14

Brand: EX Model Engines Pages: 2

Brand: Nederman Pages: 44

Brand: Hino Motors Pages: 216

Brand: Hino Pages: 278

Brand: DANA Pages: 3

Black Star 5-250

Brand: Tomahawk Pages: 24

Brand: LinMot Pages: 41

Brand: HPI Racing Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands