manualshive.com logo in svg

OPTIKON KERATRON ONDA, Installation And Operating Manual

Share
Download
OPTIKON KERATRON ONDA Installation And Operating Manual Download Page 24

Keratron

™

  Onda                                                    Installation and operating manual 

OPTIKON 2000 

Cod. 161401EN

 

5-9

 

2015-03-27 

Rev.C

 

5.3 

ELECTROMAGNETIC COMPATIBILITY TABLES 

 

5.3.1 

GUIDANCE AND MANUFACTURER'S DECLARATION 

–

ELECTROMAGNETIC EMISSIONS 

 

The  Keratron

™

    Onda  is  intended  for  use  in  the  electromagnetic  environment  specified 

below. The customer or user of the Keratron

™

  Onda should assure that it is used in such an 

environment. 
 
 

Emissions test  

Compliance 

Electromagnetic Environment 

– 

Guidance 

RF emissions 

CISPR 11 

Group 1 

The Keratron

™

 

Onda uses RF energy 

only for its  internal function. Therefore, 
its RF emissions are very low and are 
not likely to cause any interference in 
nearby electronic equipment. 

RF emissions 

CISPR 11 

Class B 

The Keratron

™

 Onda is suitable for use 

in all establishments including domestic 
establishments and those directly 
connected to the public low voltage 
supply network that supplies buildings 
used for domestic purposes.  

Harmonic emissions 

IEC 61000-3-2 

Class A 

Voltage fluctuations/Flicker 
emissions 

IEC 61000-3-3  

Complies 

 

Summary of Contents for KERATRON ONDA












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands