manualshive.com logo in svg

OPTIKON KERATRON ONDA, Installation And Operating Manual

Share
Download
OPTIKON KERATRON ONDA Installation And Operating Manual Download Page 10

Keratron

™

  Onda                                                    Installation and operating manual 

OPTIKON 2000 

Cod. 161401EN

 

3-1

 

2015-03-27 

Rev.C

 

 

3 

WARNINGS   

3.1 

GENERAL WARNINGS 

  For the correct use of the Keratron

™

 Onda system, it is necessary to 

completely read this manual. It must be used in compliance with the 
procedures and instructions described herein. 

 

  Keratron

™ 

Onda must be connected to the power supply only as specified on 

the power supply panel. Use exclusively the mains power cable provided or a 
cable that is in compliance with safety regulations.  

 

  Do not connect to the system devices or accessories different from those 

described in this manual.  

  The use of accessories or cables different from those provided with the unit 

could cause an increase in emissions or a decrease in the immunity of the 
system. The emissions originating from portable equipment for 
telecommunications could affect the unit’s performance. 

  Carefully follow the instructions for the installation and use of the unit, so as to 

prevent dangerous interference with other equipment located nearby. If this 
instrument causes dangerous interference   with other equipment ( this can be 
caused by turning the unit on and off), it is recommended that the user 
attempt to correct the interference with one or more of the following methods: 

-

  Reorient or reposition the other instruments. 

-

  Increase the distance between the instruments themselves. 

-

  Connect the unit to a power outlet that is different from the one to which the 

other instruments are connected. 

-

  Consult  the  distributor  or  authorized Optikon 2000 S.p.A.  Technical Service 

Department. 

  Keratron

™

 Onda has been developed and optimised to measure human eyes. 

The use and the evaluation of Keraton 

™

 Onda's in conditions that not comply 

with this manual, or made by using surfaces having a reflectivity   or a shape 
which  is  far  from  those  typical  of  human  eyes  (for  example:  contact  lenses  , 
surfaces  having  discontinuity  in  the  tangent  or  concavity  in  any  of  its  section 
profiles,  or  surfaces  such  to  create  multiple  reflections  or  disappearance  of 

Summary of Contents for KERATRON ONDA












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands