background image

3

1. Warranty Claim
You can find the serial number on the rear panel. In case of warranty
claim, please report this number.

2. Recording Copyright
Recording of copyrighted material for other than personal use is illegal
without permission of the copyright holder.

3. AC Fuse
The fuse is located inside the chassis and is not user-serviceable. If
power does not come on, contact your Onkyo authorized service
station.

4. Care
From time to time you should wipe off the front and rear panels and the
cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a weak
solution of mild detergent and water, wring it out dry, and wipe away
the dirt. Following this, dry immediately with a clean cloth. Do not use
rough material, thinners, alcohol or other chemical solvents or cloths
since these may damage the finish or remove the panel lettering.

5. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,
READ THE FOLLOWING SECTION CAREFULLY.
• The voltage of the available power supply differs according to

country or region. Be sure that the power supply voltage of the area
where this unit will be used meets the required voltage (e.g.,
AC230V 50Hz or AC120V 60Hz) written on the rear panel.

• Voltage Selector (Rear Panel)

Worldwide models are equipped with a voltage selector to conform
with local power supplies. Be sure to set this switch to match the
power supply in your area before plugging in the unit (see page 5).
Models without a voltage selector can only be used in areas where
the power supply voltage is the same as that of the unit.

FOR U.S. MODEL

FCC Information for User
CAUTION:

Changes or modifications not expressly approved by the manufac-
turer for compliance could void the user's authority to operate the
equipment.

NOTE:

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if net
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to ratio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between other equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FOR EUROPEAN MODEL

Precautions

FOR CANADIAN MODEL:
(POUR LE MODELE CANADIEN)

• For models having a power cord with a polarized plug

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• THIS DIGITAL APPARATUS DOES NOT EXCEED THE

CLASS B LIMITS FOR RADIO NOISE EMISSION FROM
DIGITAL APPARATUS SET OUT IN THE RADIO INTERFER-
ENCE REGULATIONS OF THE CANADIAN DEPARTMENT
OF COMMUNICATIONS.

• Sur les modèles dont la fiche est polarisée.

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS
LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQ’AU FOND.

• L'INTERFÉRENCE RADIO ÉLECTRIQUE GÉNÉRÉE PAR CET

APPAREIL NUMÉRIQUE DE TYPE B NE DÉPASSE PAS LES
LIMITES ÉNONCÉES DANS LE RÈGLEMENT SUR LES
PERTURBATIONS RADIO ÉLECTRIQUES, SECTION
APPAREIL NUMÉRIQUE, DU MINISTÈRE DES COMMUNI-
CATIONS.

ATTENTION FOR BRITISH MODEL

Replacement and mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with the
following code:
Blue:

Neutral

Brown:

Live

As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal in
the plug which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal
in the plug which is marked with the letter L or coloured RED.

IMPORTANT

A 5 amp fuse is fitted in this plug. Should the fuse need to be replaced,
please ensure that the replacement fuse has a rating of 5 amps and that
it is approved by ASTA or BSI to BS1362. Check for the ASTA mark
or the BSI mark on the body of the fuse.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE
SOCKET OUTLET IN YOUR HOME, THEN THE FUSE SHOULD
BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF
SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13
AMP SOCKET.
If in any doubt, please consult a qualified electrician.

Declaration  of  Conformity

We, ONKYO EUROPE

ELECTRONICS GmbH
INDUSTRIESTRASSE 20
82110 GERMERING,
GERMANY

declare in own responsibility, that the ONKYO product described
in this instruction manual is in compliance with the corresponding 
technical standards such as EN55013, EN55020, EN61000-3-2, -3-3 
and EN60065

GERMERING, GERMANY

ONKYO EUROPE ELECTRONICS GmbH

K.OTSU

Summary of Contents for ED-301





















Reviews: