H8BM-R
10
●
Setting Counters That Will Not Use the Machine
Stoppage Output (3-stage Type)
The machine stoppage output will not be
used for counters for which the machine
stoppage value has been set to +99999
(+9999.9 h/+9999.9 s).
●
Setting Counters That Will Not Be Used
Input and output operations will not
occur for counters for which the forecast
value has been set to 0 (0.0 h/0.0 s).
•
If the forecast value is set to 0 (0.0 h/0.0 s), the
pre-forecast and machine stoppage values will
automatically be set to 0 (0.0 h/0.0 s).
●
Setting Counters to Be Used as Total Counters/Timers
Counters can be used as total counters/
timers if the forecast value for that
counter is set to 999999 (99999.9 h/
99999.9 s).
•
The machine stoppage output will no longer be
output for that counter.
•
When using a counter as a total counter, the
forecast output for that counter when the count
value changes from 999999 to 0 will be a one-
shot output of 20 ms to indicate a carry.
Press the
Key (or turn ON the
counter No. selection input) in RUN
mode to check the count value for each
counter.
•
The counter number changes in sequence
each time the
Key is pressed (or the input turns ON), from 1 through
9, then back to 1.
Note: However, any counter whose forecast value is set to 0 (0.0 h/0.0 s) will be
skipped.
Timer Operation Display
The period on the count value display
will flash while the count input is ON and
the Timer is in h mode.
•
The timer operation measures time by totaling
the ON time of the count input.
1. Resetting Individual Counters
(1) Press the
Key (or turn ON the
counter number selection input) to
select the counter to be reset.
•
The counter value can be reset in all modes
except initial setting mode and re-monitor
mode.
(2) Press the
Key (or turn ON
the reset input) to reset the count
value to 0 for that counter only.
2. Resetting of All Counters at the Same Time
Press and hold both the
and
Keys for 3 seconds to reset the
count value for all counters to 0.
•
The same operation is achieved by
simultaneously turning ON the counter number
selection and reset inputs for 3 seconds.
Press and hold the
and
Keys for 3 seconds to reset the count
values, pre-forecast values, forecast
values, and machine stoppage values to
0 for all counters.
•
The counter number after All Clear has been
executed will automatically change to 1.
The pre-forecast value, forecast, and machine stoppage status
display will be as follows:
●
Pre-forecast Values (3-stage
Type)
The output display for counters for
which the count value has reached the
pre-forecast set value will be lit.
•
Pre-forecast values are only displayed as a
message and are not output.
●
Forecast Outputs
A red indicator will light at the top of the
output display section for the lit counter
number and the output will turn ON.
●
Machine Stoppage Output (3-
stage Type)
The entire background will alternate
between red and green and the
output display for the counter with a
machine stoppage will flash.
Note: If the pre-forecast, forecast, or machine
stoppage output turns ON, the counter
number display will automatically change
to that number and the count value will be
displayed (in RUN mode only).
4. Special Set Values
5. Checking Count Values (RUN Mode)
6. Other Indicators
0
7
99999
00
7
99999
0
9
0
0
8
999999
9000
1
100000
C
N
T
N
o.
C
N
T
N
o.
1
→
2
→
3
→
4
→
5
→
6
→
7
→
8
→
9
00
1
10000
7. Deleting Count Value
8. All Clear
9. Control Output Display
100000
8
100000
C
N
T
N
o.
0
8
100000
RESET
0
a
100000
C
N
T
N
o.
RESET
23456
3
200000
0
1
0
RESET
SET
90000
1
100000
100000
1
100000
110000
1
100000
