H8BM-R
8
Operation
Key protection and whether each counter operates as a counter or a timer are specified on a DIP switch provided on the side panel of the
Counter. Open the cover of the switch compartment on the side of the Counter to access the DIP switch.
The system will always enter the RUN mode after the power supply is turned ON.
1. DIP Switch Settings
5
4
3
2
1
6
7
8
9 10
Timer
Co
u
nter
Ena
b
led
Disa
b
led
Key Protection
(Can al
w
ays
b
e s
w
itched.)
DIP s
w
itch compartment
Note 1. Set the DIP switch (except for Key Protection) before turning
ON the power.
Changes to DIP switch settings while the Counter is operating
will be ignored. Power must be turned OFF then back ON
after changing the settings.
Changes to DIP switch settings are also enabled when
changing to initial setting mode because the same operation
is performed as when cycling the power.
2. Key protection can be set for each key. Key protection will be
performed based on the details set in the initial setting mode.
Refer to
Initial Setting Mode
on page 11.
2. Changing Mode
MODE Key
MODE
MODE Key
MODE Key
MODE Key
Key
Re-monitor mode
Refer to page 11 for
information on the initial
setting mode.
--
23456
3
200000
23456
3
200000
23456
3
500
23456
3
10000
N
ormal Mode
Key
Press for 4 s min.
Press for 4 s min.
This mode is for the operational state.
The present
v
al
u
e, set
v
al
u
e, co
u
nter n
u
m
b
er,
and o
u
tp
u
t stat
u
s
w
ill
b
e displayed.
This mode is for setting forecast
v
al
u
es.
V
al
u
es can
b
e independently set for each
co
u
nter n
u
m
b
er.
This mode is for setting pre-forecast
v
al
u
es.
The pre-forecast
w
ill
b
e displayed (LCD) as a
v
al
u
e
b
efore
the forecast
v
al
u
e. Set that
v
al
u
e as the pre-forecast
v
al
u
e.
V
al
u
es can
b
e independently set for each co
u
nter n
u
m
b
er.
Set the pre-forecast
v
al
u
e
b
y de
v
iation.
RU
N
mode
Forecast
v
al
u
e mode
Pre-forecast
v
al
u
e mode*
Machine stoppage mode*
Initial Setting Mode
SET
Refer to page 12 for
information on the
re-monitor mode.
This mode is for setting machine stoppage
v
al
u
es.
Machine stoppage (o
u
tp
u
t/LCD)
w
ill occ
u
r at a
v
al
u
e in
excess of the forecast
v
al
u
e. Set that
v
al
u
e as the
machine stoppage
v
al
u
e.
V
al
u
es can
b
e independently set for each co
u
nter n
u
m
b
er,
bu
t machine stoppage o
u
tp
u
t
w
ill
b
e performed if any
co
u
nter from
N
o. 1 to 9 reaches the machine stoppage
v
al
u
e. Set the machine stoppage
v
al
u
e
b
y de
v
iation.
Note: I/O operations are always performed regardless
of the mode.
If no key is pressed for 1 minute in each mode,
the RUN mode is automatically restored.
will flash.
The modes marked * are not provided on the 1-
stage type Counter.
3