Olympus MAJ-2301 Instructions Manual Download Page 8 | Manualshive

Page: 8 / 72

background image

4

Important Information — Please Read Before Use

MAJ-2301 INSTRUCTION MANUAL



Instrument compatibility

This instrument should be used in combination with the ancillary equipment shown in “



System chart”

on page 57. Using incompatible equipment can result in patient or operator injury and/or equipment
damage as well as malfunction.
This instrument complies with EMC standard for medical electrical equipment edition 4
(IEC 60601-1-2: 2014).



Prohibition of improper repair and modification

Never allow a person other than Olympus-qualified personnel to disassemble or modify the instrument,
as this may result in injury of the patient or operator as well as damage to the equipment. Olympus will
not assume any liability for human accident or equipment damage occurred due to repair by a person
other than Olympus-qualified personnel.



Signal words

The following signal words are used throughout this manual:

Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury. It may also be used to alert against unsafe practices or potential
equipment damage.

Indicates additional helpful information.

WARNING

CAUTION

NOTE

«
...
6
7
8
9
10
...
»

Summary of Contents for MAJ-2301









































































Reviews:

No comments

Related manuals for MAJ-2301

Brand: E-T-A Pages: 6

TRIPP LITE Series

Brand: Eaton Pages: 8

Brand: ATEN Pages: 17

EXHL-TRN-LE1 Series

Brand: Larson Electronics Pages: 2

SISTG1040-242-LRT

Brand: Transition Networks Pages: 31

Brand: Electroswitch Pages: 6

Brand: DirectConnect Pages: 10

Brand: Phonocar Pages: 2

Brand: Lantech Pages: 30

Brand: Linkskey Pages: 2

Brand: LevelOne Pages: 35

Brand: Black Box Pages: 2

Brand: Versa Technology Pages: 26

Brand: Generac Power Systems Pages: 2

OSD2251P Series

Brand: Optical Systems Design Pages: 48

Brand: Extron electronics Pages: 6

Brand: AVLinx Pages: 10

Brand: Kramer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands