Olympus MAJ-2301 Instructions Manual Download Page 32 | Manualshive

Page: 32 / 72

background image

28

3.5 Insertion of batteries into the foot switch

MAJ-2301 INSTRUCTION MANUAL

Ch.3

NOTE

• To facilitate removal of exhausted batteries from the battery compartment, pull up

the ribbon.

• In general, the battery performance drops as the temperature decreases. This is

important to note when using the instrument in a low-temperature environment.
Even when the performance of batteries drops due to a low temperature, it may
sometimes be restored when the instrument is brought back under a normal
temperature.

NOTE

• The ON and flashing conditions of the communication status indicator vary

depending on the status of communication with the wireless unit.



ON: Communication with the wireless unit is established.



Flashing or OFF: Communication with the wireless unit is not established.

• Each indicator the ON / flashing (slow) automatically turns off in about 2 minutes

and flashing (early) automatically turns off in about 3 seconds. To check again,
press one of the switches of foot switch again.

8

If the remaining battery power is almost or completely exhausted, repeat Step 1 to 7
above again.

«
...
30
31
32
33
34
...
»

Summary of Contents for MAJ-2301









































































Reviews:

No comments

Related manuals for MAJ-2301

Brand: Brightlink Pages: 33

Brand: Zektor Pages: 17

Aeotec Micro Smart Energy Switch G2

Brand: Aeon Labs Pages: 11

Brand: Witura Pages: 21

Brand: IPGARD Pages: 2

SANbox 5000 Series

Brand: Qlogic Pages: 2

Brand: Clas Ohlson Pages: 4

Brand: ddtop Pages: 10

Brand: ELPRO Pages: 8

Guard Master 440N-Z2NRS1A

Brand: Allen-Bradley Pages: 4

SecureStack B2 B2G124-48P

Brand: Enterasys Pages: 91

Brand: Pulsar Pages: 5

Brand: VigilLink Pages: 24

Brand: Whelen Engineering Company Pages: 5

Brand: Black Box Pages: 21

Brand: EMP-Centauri Pages: 4

SENSALINK SENLSS V2

Brand: Thorn Pages: 2

Brand: AMERITRON Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands