Olympus MAJ-2301 Instructions Manual Download Page 31 | Manualshive

Page: 31 / 72

background image

3.5 Insertion of batteries into the foot switch

27

MAJ-2301 INSTRUCTION MANUAL

Ch.3

Table 3.1

CAUTION

Be sure to rotate the battery compartment cover locks (× 2) all the way until it
stops. If the cover is locked insufficiently, the waterproofing becomes insufficient
and water penetration inside the equipment may damage it.

7

Press one of the switches on the foot switch until it clicks and check the battery power
indicator and communication status indicator to confirm that sufficient battery power is
remaining. These indicators light or flash according to the remaining battery power as
shown in Table 3.1.

Figure 3.13

Battery power indicator

(ON/flashing: Amber)

Communication status

indicator

(ON/flashing: Green)

Remaining battery power

OFF

ON or flashing (fast)

Battery power is sufficient.

ON

ON or flashing (fast)

Battery power is low.
Replace batteries immediately.

Flashing (slow)

ON or flashing (fast)

Battery power is hardly remaining.
Replace batteries immediately.

Flashing (fast)

OFF

Battery power is exhausting and normal
operation is unavailable.
Replace batteries immediately.

OFF

OFF

Battery power is exhausting and normal
operation is unavailable.
Replace batteries immediately.

Communication status
indicator

Battery power
indicator

«
...
29
30
31
32
33
...
»

Summary of Contents for MAJ-2301









































































Reviews:

No comments

Related manuals for MAJ-2301

Brand: CALIENT Pages: 22

EdgeSwitch 10 XP

Brand: Ubiquiti Pages: 13

Brand: Magnum Pages: 3

Cyber SWITCH 1000

Brand: Cabletron Systems Pages: 106

Brand: Accton Technology Pages: 523

Brand: IPGARD Pages: 2

Brand: Cabletron Systems Pages: 83

Brand: Pilz Pages: 8

LMX-1002G-SFP Series

Brand: ANTAIRA Pages: 22

Brand: National Instruments Pages: 12

Brand: Comm-Tec Pages: 10

Brand: Atlona Pages: 22

Brand: CoolGear Pages: 8

DG-GS4900SE Series

Brand: Digisol Pages: 23

S5700-24F-8G-4TF

Brand: Hored Pages: 28

Brand: SMART-AVI Pages: 2

Brand: Shinybow USA Pages: 32

Brand: Datacom Systems Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands