manualshive.com logo in svg

OLT 8x12 SpaceMaker, Assembly Manual

Share
Download
OLT 8x12 SpaceMaker Assembly Manual Download Page 38

Horizontal Narrow Wall 
Trim dado (notch) comes 
together with protruding 
edge of Door Header.

68.

  Attach 

Horizontal Door Trim

 and 

Horizontal Narrow 

Wall Trim

 onto the exposed part of the Door Header, and 

tight under the lip of the Drip Cap. Secure Horizontal Door 
Trim with 

5 - 1 1/2” Finishing Nails

 and the short Narrow 

Wall Trims with 

2 - 1 1/2” Finishing Nails 

per piece.

Parts

 

Horizontal Door Trim 

(1/2” x 1 1/2” x 64”) 

x 1 

Horizontal Narrow Wall Trim 

(7/8” x 3” x 9”) 

x 2 

- Dado Edge

Hardware 

N1

 

- 1 1/2” Finishing Nails

 

x 9 total

Square Cut Facia

Angled Facia

Angled Facia caps 
Square Cut Facia.

69.

  Position 

Rear Facia 

(angle cut on ends) and 

Side Facia

 

(square cut ends) in corner.  Line Facia up so angle cut Facia 
caps square cut Facia.  Attach angled Facia to Nailing Strip with 

8 - 1 1/2” Finishing Nails

 per piece.  Gap where facia boards 

come together at peak will be covered in 

Step 71.  

Do a dry run 

using Side Facia to help you correctly position before attaching.

Parts (Steps 69 - 70)

 

Front & Rear Facia 

- Angle Cut Ends

 

(3/4” x 3 1/2” x 58”) 

x 4 

Side Facia 

(3/4” x 3 1/2” x 71 3/4”) 

x 4

Hardware (Steps 69 - 70) 

N1

 

- 1 1/2” Finishing Nails

 x 64 total

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 38

Summary of Contents for 8x12 SpaceMaker















































Reviews:

No comments

Brands by name

Popular brands

Load more brands