manualshive.com logo in svg

OLT 8x12 SpaceMaker, Assembly Manual

Share
Download
OLT 8x12 SpaceMaker Assembly Manual Download Page 12

14. 

For each 

Solid Wall Panel

, carefully lay panel 

face down.  Position and attach a 

Bottom Wall 

Plate

 to bottom of wall studs of each wall panel with 

3 - 2 1/2” Screws

.  Position so plates are flush with 

framing.

Parts

 

Solid Wall Panels 

(45 1/2” x 75”) 

x 7

 

Bottom Wall Plates

 

(1 1/2” x 2 1/2” x 45 1/2”) 

x 7

Hardware 

S1

 

- 2 1/2” Screws

 

x 21 total

Important:

 

Pilot hole ALL 2x3 Wall 

Studs with 1/8” drill bit prior 

to screwing. This will make it 

much easier to attach 

together.

 

Pilot Hole 

first.

Bottom Wall Plate

Side of Shed

1st Side 
Wall Panel

Front of Shed

1st Side Wall Panel

Rear of shed

2x3 wall frame

Flush with 
Floor Framing

1/2” 
overhang

Important -

 Make sure all walls are aligned 

in their upright position.  If not, water may 
leak into your shed. Unsure if panel is  
facing up or down?  Compare solid wall 
siding to window wall siding and match  
orientation.

15.

  Starting at Rear Corner, position a Solid Side Wall panel on top of Plywood Floor.  The Wall Panel 

bottom framing will sit flush with Floor framing.  Wall siding will overhang the floor.  The Side Wall panels 
will sit flush at the end of the Plywood Floor with the Rear Wall panels sandwiched between them. 

Note:

 Siding will overhang the Floor by approximately 1/2”. 

Do Not Attach Walls To 
Floor Until Step 23

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 12

Summary of Contents for 8x12 SpaceMaker















































Reviews:

No comments

Brands by name

Popular brands

Load more brands