manualshive.com logo in svg

OLT 8x12 SpaceMaker, Assembly Manual

Share
Download
OLT 8x12 SpaceMaker Assembly Manual Download Page 29

48. 

One the Metal Roof is spaced correctly from side-to-side and top-to-bottom, lift 3 panels 

up and run a bead of caulking down the overlapping seams of each panel to seal the joints. 
Place panels down one by one once seam is caulked. You will likely need assistance from a 
helper for this step. Caulk each seam.

Bead of caulking

49. 

Using 

8 - 2” Metal Screws

 and 

1/4” Nut Driver

 (included), partially secure Metal Roof 

Panels to 2nd row of battens from top. Only fasten screws halfway so that Metal Roof Hangers 
can be removed. Metal screw is self-tapping, screw into center of Battens at peak of Roof  
panels.

Important Metal Roof Hangers 
will be removed in Step 50.

50. 

Before fully securing roof panels, remove Metal Roof Hangers from Roof.

Important: Remove Metal Roof Hangers.

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 29

Summary of Contents for 8x12 SpaceMaker















































Reviews:

No comments

Brands by name

Popular brands

Load more brands