Olivetti FK-507 Page 99 Service Manual Download

Page: 99 / 118

8. Troubleshooting

Field Service Ver. 2.0 Dec. 2008

FK-507

roubleshooting

Code

Description

Cause

Remedy

Re Li Lo

• Received DIS or DTC 3

times while waiting for
response to TCF

• No response even after

sending TSI/DCS and
TCF 3 times

• Received FTT twice even

TCF has lowest speed

Failure in remote
machine

Try another remote machine.

Line failure

Try another line.

Failure in FAXU board

Replace FAXU board

Failure in MFBU board

Replace MFBU board

• Reverse polarity while

waiting for signal other
than initial identification

Failure in remote
machine

Check the remote system
and retry TX.

Line failure

If same error is experienced
several times, set the soft
switch to (MODE 082 Bit 3)
0.

• No response to post mes-

sage (T4 timeout)

• 5 minute timeout in RNR,

RR sequence (T5 timeout)

Failure in remote
machine

Try another remote machine.

No RTC detection in
remote machine (line
failure)

Try another line.

• Received DCN while wait-

ing for response to post
message

Interruption or failure
in remote machine

Check the status of the
remote machine and retry
TX.

• Received PIP for post

message (For response to
EOP or PPS-EOP, com-
munication is normal even
though error code is dis-
played)

Failure in remote
machine

Check the status of the
remote machine.

• Received RTN for post

message (where RTN
reception is regarded as
communication failure)

• Retry out of resending

error

• PPR frame error

Failure in remote
machine

Check the status of the
remote machine.

Line failure

Check the line.

Failure in TX level

Check TX level.

• Received CRP 3 times for

TCF

• Received CRP 3 times for

post message

• Received CRP 3 times for

DTC of polling reception

Failure in remote
machine

Try another remote machine.

Line failure

Try another line.

• RX command error (with-

out cutting off carrier)

Failure in remote
machine

Check the status of the
remote machine.

• No remote machine

response after changing
mode (T1 timeout)

Failure in remote
machine

Check the status of the
remote machine.

• Received PIN for post

message

Failure in remote
machine

Check the status of the
remote machine.

Service Manual Y109

1-7

Summary of Contents for FK-507






















































































































Search results

Summary of Contents for FK-507

Reviews:

Related manuals for FK-507

Brands by name

Popular brands

Olivetti FK-507, Service Manual

Search results

Summary of Contents for FK-507

Reviews:

Related manuals for FK-507

Brands by name

Popular brands