Olivetti FK-507 Page 100 Service Manual Download

Page: 100 / 118

Field Service Ver. 2.0 Dec. 2008

8. Troubleshooting

FK-507

roubleshooting

8.2.4

Communication errors (RX)

Code

Description

Cause

Remedy

Re Li Lo

• Protocol failure in V.34

sequence

Failure in remote
machine

Try another remote machine.

Line failure

Try another line.

• T1 timeout while waiting

for initial identification sig-
nal

Failure in remote
machine

Try another remote machine.

Line failure

Try another line.

• Received DCN while wait-

ing for commands other
than DCN in phase B

Interruption or failure
in remote machine

Check the status of the
remote machine and retry TX.

• Detected low speed flag

followed by 10 sec. time-
out while waiting for detec-
tion of image signal carrier
(HMCD ON)

Failure in remote
machine

Try another remote system.

Line failure

Try another line.

• Carrier disconnected for

15 seconds while receiv-
ing G3 image signal

Error in remote
machine

Ask for resending.

Failure in remote
machine

Try another remote machine.

Line failure

Try another line.

• T2 timeout while waiting

for post message

• T2 timeout while waiting

for DCN after receiving
last page

• No response from remote

system after changing
mode (T2 timeout)

Error in remote
machine

Try another remote machine.

Accidental RTC detec-
tion (line failure)

Try another line.

• Received DCN while wait-

ing for command other
than DCN in phase D

Interruption or failure
in remote machine

Ask for resending.

• Received PRI-Q as post

message (Communica-
tion is regarded as nor-
mal even with error
message)

Failure in remote
machine

Check the status of the
remote machine.

• Cannot decode line cor-

rectly for 35 seconds while
receiving ECM image sig-
nal

Failure in remote
machine

Try another remote machine.

Line failure

Try another line.

Failure in FAXU board

Replace FAXU board

Failure in MFBU board

Replace MFBU board

• Received CRP 3 times

while waiting for initial
identification signal

Failure in remote
machine

Try another remote machine.

Failure in FAXU board

Replace FAXU board

Failure in MFBU board

Replace MFBU board

Line failure

Try another line.

Y109971-7 Sevice Manual

Summary of Contents for FK-507






















































































































Search results

Summary of Contents for FK-507

Reviews:

Related manuals for FK-507

Brands by name

Popular brands

Olivetti FK-507, Service Manual

Search results

Summary of Contents for FK-507

Reviews:

Related manuals for FK-507

Brands by name

Popular brands