Oliver 6320 Owner'S Manual Download Page 34

 

34 | 

Page 

Oliver Machinery 

6320 Sander

 

Operation / Quality-Related Issues 

Problem  

Possible Cause  

Solution  

Work pulled from hand.  

Inadequate stock 
support. 

Hold the stock firmly against the sanding belt. 

Use the miter gauge as support. 

Use special jigs to support the short stock. 

Sanded edge is not 
square. 

Sanding belt is not 
perpendicular to the 
table. 

Adjust the sanding belt tilt.  

Digital readout not 
zeroed. 

Set the sanding belt in the upright position and 
reset the digital readout.   

Improper stock feeding. 

Ensure stock is pressed firmly against the table 
when feeding. 

Unable to form a 
straight edge. 

Improper stock feeding.  

Apply  even  and  consistent  pressure  on  the 
entire edge when feeding.  

Worn graphite backing. 

Use a straight edge to check the flatness of the 
platen with the graphite backing. Replace worn 
graphite backing as needed. 

Stock burns  

Sanding grit is too fine. 

Use a sanding belt with a coarser grit. 

Clogged/worn sanding 
belt. 

Use the sanding belt cleaner to unclog the belt. 
Replace the sanding belt as needed. 

Feed pressure is too 
high. 

Lower feed pressure. 

Sanding belt clogs easily 

Sanding softwood or 
wood with high resin 
content.  

Clean/replace the belt more frequently. 

Sanding wet stock. 

Dry stock before sanding. 

Sanding non-wood 
materials. 

Some materials may melt easily when heated. 
Sand with light pressure and keep it cool when 
sanding.  

Deep sanding marks on 
the workpiece 

Sanding belt grit is too 
coarse. 

Use a finer grit sanding belt. 

Dirty/contaminated 
sanding belt. 

Clean sanding belt. Replace as necessary. 

Too much feeding 
pressure and/or abrupt 
feeding.  

Reduce feeding pressure and allow more time 
for  the  abrasive  surface  to  work  on  the 
workpiece.  

Abrasive materials rub 
off the belt easily 

Aged sanding belt. 

Avoid  storing  sanding  belts  in  extreme 
temperatures  and  humidity,  which  may  cause 
the belt to fail prematurely. 
Do not fold or smash the sanding belt, as it may 
disintegrate the bonding material on the belt. 

 

 

 

 

Summary of Contents for 6320

























































Reviews: