Okofen PELLETRONIC TOUCH Operating Manual Download Page 50

Page: 50 / 108

Description of the heating controller module

17.5 Assembly and disassembly of the heating controller board

It is possible to take off the heating controller board from the controller casing without disconnecting the inputs and
outputs.

Make sure the heating system is powered down.

Electrostatic discharge damage

Before starting work, touch a grounded object to avoid
damage to the insulation board by electrostatic charging.

Open the cover plate of the heating controller.
See previous chapter

17.4 Assembly or disassembly of the power supply, page 49

Pull all the plugs in from the circuit board. Leave the plugs with the wiring in the casing.

Disassemble of the power supply (optional)
See previous chapter

17.4 Assembly or disassembly of the power supply, page 49

Disassemble the circuit board from the heating controller.

The installation of a new circuit board should be in reverse order.

Operating manual Pelletronic Touch

E1389EN 2.0

Summary of Contents for PELLETRONIC TOUCH













































































































Search results

Summary of Contents for PELLETRONIC TOUCH

Reviews:

Related manuals for PELLETRONIC TOUCH

Brands by name

Popular brands

Okofen PELLETRONIC TOUCH, Operating Manual

Search results

Summary of Contents for PELLETRONIC TOUCH

Reviews:

Related manuals for PELLETRONIC TOUCH

Brands by name

Popular brands