Okofen PELLETRONIC TOUCH Operating Manual Download Page 31

Page: 31 / 108

Solar

10.3 Yield - Solar Energy

This function measures the yield of the solar thermal system and displays current energy and logs previous days.

Note

For the function solar energy it is necessary to install:

• Pulse volume meter (must be connected to

24 VOLT

and

Z_IN

)

• Flow temperature sensor

• Return temperature sensor

Yield - Solar Energy

is in the menu Solar.

Yield measuring of solar energy has following menu
items:

• Actual

Display of the current solar energy, refreshes every
60 sec.

• Yield - Day

Display of todays solar energy since 00:00.

• Yield - Day before

Display of the of yesterdays solar energy.

• Yield since

Display of the solar energy since the last set date.

• Flow rate

Display of the current flow rate, refreshes every
60 sec.

• Flow temperature

Display of the current flow temperature

• Return temperature

Display of the current return temperature

E1389EN 2.0

Operating manual Pelletronic Touch

Summary of Contents for PELLETRONIC TOUCH













































































































Search results

Summary of Contents for PELLETRONIC TOUCH

Reviews:

Related manuals for PELLETRONIC TOUCH

Brands by name

Popular brands

Okofen PELLETRONIC TOUCH, Operating Manual

Search results

Summary of Contents for PELLETRONIC TOUCH

Reviews:

Related manuals for PELLETRONIC TOUCH

Brands by name

Popular brands