background image

48

Model Geopro SH

Extra heat button

Cold water

H2 Supply water

H1 Supply water

El. heater

Ground

El. heater

Compressor

  C

ondenser

Superhea

ter

M2

M7

M9

M4

M10

S2

S1

M8

DV

M5

M12

M8

M7

M2

M10

M11

Heating a real estate and domestic hot water 

Controller  has two heating circuits (H1 and H2). The lower part of 
the heating boiler is warmed up with compressor and, if needed, 
with the electrical heating resistor (S1) so that enough heat is provi-
ded to the heating system according to the current need.  The upper 
part of theboiler is heated by a compressor and, if necessary, by me-
ans of an electric heater S1, so that hot domestic water is obtained. 

Getting ready for excessive consumption of hot domestic water:  

 

When it is expected to have higher hot domestic water consumption 

than normal, heating can be boosted with additional warming. This 
is activated by pressing the separate switch. 

Setting

Factory 

setting

Range

Explanation

GH control

Compres-

sor and 

El.heater

You can choose whether the ground heating is controlled by a com-
pressor only or by an electric heater only, or whether an electric 
heater is used with the compressor.

Boiler Top winter

65

30... 75 °C

Setting value of the  Boiler Top when the outdoor temp. is  <  -20°C.

Boiler Top summer

55

30... 75 °C

Setting value of the  Boiler Top when the outdoor temp. is  > +20°C.

Hot water hysteresis

5°C

3...10°C

Hysteresis of the top part of the heating boiler control

Boiler Down hysteresis

5 °C

3...7 °C

Hysteresis of the down part of the heating boiler control.

Boiler Down MIN limit

30

30...55°C

Minimum temperature of the lower part of theboiler.

Compressor Stop

55°C

45...55°C

When the temperature of the lower part of the boiler (meas. 10) is 
exceeded this setpoint always stops the compressor, even if the top 
of the boiler commands the compressor to start.

Boiler Top hysteresis heating 
resistor

3 °C

0...10°C

The electric heater starts when the temperature at the top of the 
boiler drops amount of [”Hot water hysteresis” + ”Boiler Top hystere-
sis heating resistor”] below the calculated “Boiler top setting” value.

El. Heat  start up delay

30

0 ... 120  min.

The temperature of the middle part of the boiler (measurement 11) is 
able to switch the electrical heating resistor on only when the com-
pressor has been running the time (minutes) set here.

Extra heating

Extra heating time

50 

2

40...55°C 

0...  6h

When the “Extra heating” button is pressed, the minimum tempe-
rature setpoint (Boiler Down MIN limit) at the bottom of the boiler 
changes to the “Extra heating” setpoint (eg 45 ° C) for the duration 
of the “Extra heating time” setpoint. This operation also makes the 
lower part of the DHW boiler hotter, which increases the hot water 
capacity.

Dividing ventil pre-open

40%

25...100%

Pre-opening degree of the Dividing Valve. The pre-opening is per-
formed before the electric heater is switched on

Dividing ventil close prevent 

60s

30...240s

Closing prevent time of the DV after pre-opening.  The time calcula-
tion starts when the electric heater is switching ON.

Boiler Top setting

Calculated

Boiler Top setting is determined according to the ”Boiler Top summer 
”and ”Boiler Top  winter ” setting (see figure).

50

...

-30  

-20

  -10   0   10   

20

      30     Outd.t.

°C

Boiler Top

60

65

70

55

Boler Top setting

°C

Status

You can check what asks for or prevents the compressor and / or electric heater from turning 
on. Start and stop delays are also displayed. In addition, the running time / on of the compres-
sor and the electric heater is displayed.

Summary of Contents for S203





























































Reviews: