Octane Fitness Q35 Service Manual Download Page 40

Page: 40 / 45

40
Octane Fitness Confidential

1-800-68-634

3.12 Brake Cable Adjustment

1. Using the Level - button, make sure the resistance is set to level 1 (the lowest level).

2. Unplug the unit and remove the shrouds to access the inside.

3. Check that the brass nipple at the end of the brake cable rests in the slot of the tension slide housing.

4. The brake adjuster must be at the bottom of the slot at resistance level 1, as shown in Figure 3.19. If it is not at the

bottom of the slot, free up the cable-adjusting sleeve by backing off (loosening) the lock nut.

5. Rotate the adjuster barrel to make sure the brass nipple and the brake adjuster are touching.

6. Turn the adjuster barrel so that the brake adjuster is all the way at the top of the tension slide housing.

7. Re-tighten the lock nut to hold the adjuster barrel in place.

8. Plug in the unit and use the Level +/- buttons to test resistance changes, making sure the brake adjuster returns to

the bottom of the slot when the machine is at level 1.

Figure 3.19

Cable installed

correctly; brake

adjuster at level 1

Lock Nut

Adjuster

Barrel

Brass

Nipple

Axle

Bolt

Summary of Contents for Q35














































Search results

Summary of Contents for Q35

Reviews:

Related manuals for Q35

Brands by name

Popular brands

Octane Fitness Q35, Service Manual

Search results

Summary of Contents for Q35

Reviews:

Related manuals for Q35

Brands by name

Popular brands