Oce TDS100 User Manual Download | Manualshive

Page: 51 / 70

background image

Maintain the Océ TDS100

51

Clean the transparent plate

Introduction

You need to keep the transparent plate clean. A dirty transparent plate causes
a decreased copy quality.

When to do

Clean the transparent plate when you have spots on the copies that are not on
the original.

Required tools

'Océ cleaner A', part of cleaning kit with codenumber 1068117.

2 lint-free cloths

Attention:

Use 'Océ cleaner A' to reach the best results.

Attention:

Make sure you do not damage the sensor at the centre of the

transparent plate.

How to clean the transparent plate

1.

Turn off the Océ TDS100

2.

Pull the top cover towards you and lift the top cover to open it.

[32] Open the top cover

[32] Open the top cover

«
...
49
50
51
52
53
...
»

Summary of Contents for TDS100







































































Reviews:

No comments

Related manuals for TDS100

Brand: Olivetti Pages: 6

Brand: Sharp Pages: 4

AL-1010 - B/W Laser - Copier

Brand: Sharp Pages: 12

Brand: Sharp Pages: 30

AL-1041 - B/W Laser Printer

Brand: Sharp Pages: 47

AL 1000 - B/W Laser Printer

Brand: Sharp Pages: 47

Brand: Sharp Pages: 50

AL 800 - B/W Laser - Copier

Brand: Sharp Pages: 51

Brand: Sharp Pages: 93

Brand: Sharp Pages: 70

Brand: Ricoh Pages: 46

Brand: Ricoh Pages: 88

Brand: Develop Pages: 103

Brand: Xerox Pages: 2

C123 Copycentre

Brand: Xerox Pages: 2

Brand: Gestetner Pages: 168

Brand: Canon Pages: 104

Brand: Toshiba Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands