Oce TDS100 User Manual Download Page 33 | Manualshive

Page: 33 / 70

background image

Use the Océ TDS100

33

Check the copy quality with a test strip

Introduction

Before you start your copy job, you can check the result of your settings on the
copy quality with a test strip.

Attention:

If the original contains a filing strip, make sure that the filing

strip is at the trailing edge (see ‘Adjust leading and trailing strips’ on
page 29).

How to make a test strip

1.

Place the original centrally and face down on the original feed table.
The Océ TDS100 moves the original to the back.

[12] Feed the original centrally and face down

[12] Feed the original centrally and face down

2.

Press the 'Cut' key to select 'Standard'

3.

Press the upper side of the adjustment key
The text 'TEST' appears on the display.

4.

Press the green start button to copy a strip.

Result

The Océ TDS100 copies only a strip of the original.

«
...
31
32
33
34
35
...
»

Summary of Contents for TDS100







































































Reviews:

No comments

Related manuals for TDS100

Brand: Panasonic Pages: 84

Brand: Ricoh Pages: 12

Brand: Ricoh Pages: 10

Brand: Ricoh Pages: 212

Brand: Ricoh Pages: 548

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands