Oce TDS100 User Manual Download Page 30 | Manualshive

Page: 30 / 70

background image

30

User manual

How to add or remove a leading strip

1.

Place the original centrally and face down on the original feed table.
The Océ TDS100 moves the original to the back.

[10] Feed the original with leading strip centrally and face down

[10] Feed the original with leading strip centrally and face down

2.

Use the 'Strip' key to select 'Leading'

3.

Use the adjustment key to add or remove a leading strip
A positive value adds a strip, a negative value removes a strip

4.

Press the green start button to start the copy job.

How to add or remove a trailing strip

1.

Place the original centrally and face down on the original feed table.
The Océ TDS100 moves the original to the back.

[11] Feed the original with trailing strip centrally and face down

[11] Feed the original with trailing strip centrally and face down

2.

Use the 'Strip' key to select 'Trailing'

3.

Use the adjustment key to add or remove a trailing strip.
A positive value adds a strip, a negative value removes a strip.

4.

Press the green start button to start the copy job.

«
...
28
29
30
31
32
...
»

Summary of Contents for TDS100







































































Reviews:

No comments

Related manuals for TDS100

DocuColor DocuColor 4

Brand: Xerox Pages: 17

MultiXpress X4 Series

Brand: Samsung Pages: 609

Book Copying Easel 45/30

Brand: Kaiser Pages: 6

Brand: Canon Pages: 99

Brand: Canon Pages: 118

Brand: Fuji Xerox Pages: 77

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands