Oce TDS100 User Manual Download Page 56

Page: 56 / 70

User manual

Supported original types and sizes

Overview of supported original types and sizes

[3] The supported original types and sizes of the Océ TDS100

Overview of the conditions of the originals

[4] The conditions of the originals

Parameter

Minimum value

Recommended maximum
value

Width

210 mm (8.5”)

1000 mm (40”)

Length

279 mm (10”)

3000 mm (10”)
(maximum value: 30 m)

Length in
retention

1200 mm (48”)

Thickness

0.05 mm

1.5 mm

Weight

60 g/m

120 g/m

(maximum value: 210 g/m

)

Topic

Reccommendation

Curl

Feed curled originals extra careful.
When the diameter of a curl is less than 50 mm, use a
carrier sheet.

Paste up

Make sure that paste up's are completely pasted on all
edges or use a carrier sheet

Filing strip

Filing strips are allowed on all edges, the maximum
diameter of the hole is 36 mm

Border

Use a carrier sheet when the border is damaged, contains
reinforcement strips with holes bigger than 36 mm, or
punching holes

Fold

Shadows of the folds may be visible on the copy

Fragile or thin
media

Use a carrier sheet

Summary of Contents for TDS100







































































Search results

Summary of Contents for TDS100

Reviews:

Related manuals for TDS100

Brands by name

Popular brands

Oce TDS100, User Manual

Search results

Summary of Contents for TDS100

Reviews:

Related manuals for TDS100

Brands by name

Popular brands