NXP Semiconductors LPC822M101JDH20 User Manual Download Page 435

Page: 435 / 487

UM10800

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 1.2 — 5 October 2016

435 of 487

NXP Semiconductors

UM10800

Chapter 30: LPC82x ROM API ADC drivers

30.4.12 ADC ROM driver variables

30.4.12.1 ADC_CONFIG_T channel configuration structure

typedef struct {

uint32_t system_clock; // System clock

uint32_t adc_clock; // ADC clock (set system_clock >= adc_clock)

uint32_t async_mode;

uint32_t tenbit_mode;

uint32_t lpwr_mode;

uint32_t input_sel;

uint32_t seqa_ctrl;

uint32_t seqb_ctrl;

uint32_t thrsel;

uint32_t thr0_low;

uint32_t thr0_high;

uint32_t thr1_low;

uint32_t thr1_high;

uint32_t error_en;

uint32_t thcmp_en;

uint32_t channel_num;

} ADC_CONFIG_T;

The variables in this structure are defined as follows:

system_clock

: Frequency of the system clock generated by the SYSCON block in Hz.

adc_clock

: Frequency of the ADC clock in Hz. This is the clock rate for analog-to-digital

conversions. Maximum clock rate is 50 MHz for 12-bit resolution. In synchronous mode,
ensure that

system_clock

adc_clock

async_mode

: 0 selects synchronous mode, 1 selects asynchronous mode. See

Table 280

tenbit_mode

: 0 disables 10-bit mode, 1 enables fast-conversion, 10-bit mode. See

Table 280

lpwr_mode

: 0 disables low-power mode, 1 enables low-power mode. See

Table 280

inp_sel

: selects input for channel 0.

0x0 = ADCn_0 pin.

0x1 = Reserved.

0x2 = Reserved.

0x3 = Reserved.

0x4 =Reserved.

seqa_ctrl

: Register content of the SEQA_CTRL register. See

Table 281

. Ensure that

the START and SEQA_EN bits are always set to 0.

seqb_ctrl

: Register content of the SEQB_CTRL register. See

Table 281

. Ensure that

the START and SEQB_EN bits are always set to 0.

thrsel

: Register content of the CHAN_THRSEL register. See

Table 290

thr0_low

: Low threshold 0 value.

thr0_high

: High threshold 0 value.

Summary of Contents for LPC822M101JDH20








































































































































































































































































































































































































































































































Search results

Summary of Contents for LPC822M101JDH20

Reviews:

NXP Semiconductors LPC822M101JDH20, User Manual, Page: 435 / 487

Search results

Summary of Contents for LPC822M101JDH20

Reviews: