NXP Semiconductors LPC5411 Series Product Data Sheet Download Page 42 | Manualshive

Page: 42 / 105

background image

LPC5411x

All information provided in this document is subject to legal disclaimers.

© NXP Semiconductors N.V. 2018. All rights reserved.

Product data sheet

Rev. 2.1 — 9 May 2018

42 of 105

NXP Semiconductors

LPC5411x

32-bit ARM Cortex-M4/M0+ microcontroller

•

PWM features:

–

Counters can be used in conjunction with match registers to toggle outputs and
create time-proportioned PWM signals.

–

Up to eight single-edge or four dual-edge PWM outputs with independent duty
cycle and common PWM cycle length.

•

Event creation features:

–

The following conditions define an event: a counter match condition, an input (or
output) condition such as an rising or falling edge or level, a combination of match
and/or input/output condition.

–

Selected events can limit, halt, start, or stop a counter or change its direction.

–

Events trigger state changes, output toggles, interrupts, and DMA transactions.

–

Match register 0 can be used as an automatic limit.

–

In bi-directional mode, events can be enabled based on the count direction.

–

Match events can be held until another qualifying event occurs.

•

State control features:

–

A state is defined by events that can happen in the state while the counter is
running.

–

A state changes into another state as a result of an event.

–

Each event can be assigned to one or more states.

–

State variable allows sequencing across multiple counter cycles.

7.20.3 Windowed WatchDog Timer (WWDT)

The purpose of the Watchdog Timer is to reset or interrupt the microcontroller within a
programmable time if it enters an erroneous state. When enabled, a watchdog reset is
generated if the user program fails to feed (reload) the Watchdog within a predetermined
amount of time.

7.20.3.1

Features

•

Internally resets chip if not reloaded during the programmable time-out period.

•

Optional windowed operation requires reload to occur between a minimum and
maximum time period, both programmable.

•

Optional warning interrupt can be generated at a programmable time prior to
watchdog time-out.

•

Programmable 24-bit timer with internal fixed pre-scaler.

•

Selectable time period from 1,024 watchdog clocks (T

WDCLK

× 256 × 4) to over 67

million watchdog clocks (T

WDCLK

× 2

24

× 4) in increments of four watchdog clocks.

•

“Safe” watchdog operation. Once enabled, requires a hardware reset or a Watchdog
reset to be disabled.

•

Incorrect feed sequence causes immediate watchdog event if enabled.

•

The watchdog reload value can optionally be protected such that it can only be
changed after the “warning interrupt” time is reached.

•

Flag to indicate Watchdog reset.

«
...
40
41
42
43
44
...
»

Summary of Contents for LPC5411 Series










































































































Reviews:

No comments

Related manuals for LPC5411 Series

Brand: Parker Pages: 30

Brand: Gardena Pages: 18

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 23

Brand: Warren Controls Pages: 28

Brand: EAS Electric Pages: 89

Brand: vacuubrand Pages: 12

Brand: Vacon Pages: 47

Brand: Vacon Pages: 40

Bell & Gossett Technologic PPS

Brand: Xylem Pages: 20

Brand: Case IH Pages: 81

Brand: Rabbit Pages: 12

Brand: Kelly Pages: 35

Brand: DROPSA Pages: 29

Brand: NEC Pages: 265

Brand: National Instruments Pages: 8

AMBITECH BRAKE-PAK

Brand: TIE Pages: 5

GL8-GL8000M3-RCA-3.0

Brand: Balboa Instruments Pages: 9

WB-150-IPW-1B-2

Brand: watt box Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands