NXP Semiconductors LPC5411 Series Product Data Sheet Download Page 34 | Manualshive

Page: 34 / 105

background image

LPC5411x

All information provided in this document is subject to legal disclaimers.

© NXP Semiconductors N.V. 2018. All rights reserved.

Product data sheet

Rev. 2.1 — 9 May 2018

34 of 105

NXP Semiconductors

LPC5411x

32-bit ARM Cortex-M4/M0+ microcontroller

7.16 General Purpose I/O (GPIO)

The LPC5411x provides two GPIO ports with a total of 48 GPIO pins.

Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The current level
of a port pin can be read back no matter what peripheral is selected for that pin.

See

for the default state on reset.

7.16.1 Features

•

Accelerated GPIO functions:

–

GPIO registers are located on the AHB so that the fastest possible I/O timing can
be achieved.

–

Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.

–

All GPIO registers are byte and half-word addressable.

–

Entire port value can be written in one instruction.

•

Bit-level set, clear, and toggle registers allow a single instruction set, clear or toggle of
any number of bits in one port.

•

Direction control of individual bits.

•

All I/O default to inputs after reset.

•

All GPIO pins can be selected to create an edge or level-sensitive GPIO interrupt
request.

•

One GPIO group interrupt can be triggered by a combination of any pin or pins.

7.17 Pin interrupt/pattern engine

The pin interrupt block configures up to eight pins from all digital pins for providing eight
external interrupts connected to the NVIC. The pattern match engine can be used in
conjunction with software to create complex state machines based on pin inputs. Any
digital pin, independent of the function selected through the switch matrix can be
configured through the SYSCON block as an input to the pin interrupt or pattern match
engine. The registers that control the pin interrupt or pattern match engine are located on
the I/O+ bus for fast single-cycle access.

«
...
32
33
34
35
36
...
»

Summary of Contents for LPC5411 Series










































































































Reviews:

No comments

Related manuals for LPC5411 Series

Brand: D-Link Pages: 113

Brand: D-Link Pages: 146

Brand: NEC Pages: 304

Brand: WAGO Pages: 414

Brand: V2 Pages: 48

Brand: I-Tork Pages: 15

Brand: SOMFY Pages: 4

Brand: Fuji Electric Pages: 12

Brand: Apricus Pages: 32

Linear Technology ADI Power DC3017A

Brand: Analog Devices Pages: 12

SYSVRF AHU 10HP S

Brand: SystemAir Pages: 16

Brand: Zapi Pages: 30

Brand: Nations Pages: 654

Brand: Powtran Pages: 36

Brand: National Instruments Pages: 18

PROFOX PF-M100X

Brand: AUMA Pages: 56

Brand: SUNWIND Pages: 53

Brand: Unitech Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands