NXP Semiconductors LPC5411 Series Product Data Sheet Download Page 24

Page: 24 / 105

LPC5411x

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 2.1 — 9 May 2018

24 of 105

NXP Semiconductors

LPC5411x

32-bit ARM Cortex-M4/M0+ microcontroller

7.8 System Tick timer (SysTick)

The ARM Cortex-M4 and ARM Cortex-M0+ cores include a system tick timer (SysTick)
that is intended to generate a dedicated SYSTICK exception. The clock source for the
SysTick can be the system clock or the SYSTICK clock.

7.9 On-chip static RAM

The LPC5411x supports up to192 KB SRAM with separate bus master access for higher
throughput and individual power control for low-power operation.

7.10 On-chip flash

The LPC5411x supports up to 256 KB of on-chip flash memory.

7.11 On-chip ROM

The 32 KB on-chip ROM contains the boot loader and the following Application
Programming Interfaces (API):

•

In-System Programming (ISP) and In-Application Programming (IAP) support for flash
programming.

•

ROM-based USB drivers (HID, CDC, MSC, and DFU). Flash updates via USB is
supported.

•

Supports booting from valid user code in flash, USART, SPI, and I

•

Legacy, Single, and Dual image boot.

Summary of Contents for LPC5411 Series










































































































Search results

Summary of Contents for LPC5411 Series

Reviews:

Related manuals for LPC5411 Series

Brands by name

Popular brands

NXP Semiconductors LPC5411 Series, Product Data Sheet

Search results

Summary of Contents for LPC5411 Series

Reviews:

Related manuals for LPC5411 Series

Brands by name

Popular brands