NXP Semiconductors LPC5411 Series Product Data Sheet Download Page 35 | Manualshive

Page: 35 / 105

background image

LPC5411x

All information provided in this document is subject to legal disclaimers.

© NXP Semiconductors N.V. 2018. All rights reserved.

Product data sheet

Rev. 2.1 — 9 May 2018

35 of 105

NXP Semiconductors

LPC5411x

32-bit ARM Cortex-M4/M0+ microcontroller

7.17.1 Features

•

Pin interrupts:

–

Up to eight pins can be selected from all GPIO pins on ports 0 and 1 as
edge-sensitive or level-sensitive interrupt requests. Each request creates a
separate interrupt in the NVIC.

–

Edge-sensitive interrupt pins can interrupt on rising or falling edges or both.

–

Level-sensitive interrupt pins can be HIGH-active or LOW-active.

–

Level-sensitive interrupt pins can be HIGH-active or LOW-active.

–

Pin interrupts can wake up the device from sleep mode and deep-sleep mode.

•

Pattern match engine:

–

Up to eight pins can be selected from all digital pins on ports 0 and 1 to contribute
to a boolean expression. The boolean expression consists of specified levels
and/or transitions on various combinations of these pins.

–

Each bit slice minterm (product term) comprising of the specified boolean
expression can generate its own, dedicated interrupt request.

–

Any occurrence of a pattern match can also be programmed to generate an RXEV
notification to the CPU. The RXEV signal can be connected to a pin.

–

Pattern match can be used in conjunction with software to create complex state
machines based on pin inputs.

–

Pattern match engine facilities wake-up only from active and sleep modes.

7.18 AHB peripherals

7.18.1 DMA controller

The DMA controller allows peripheral-to memory, memory-to-peripheral, and
memory-to-memory transactions. Each DMA stream provides unidirectional DMA
transfers for a single source and destination.

7.18.1.1

Features

•

20 channels, 19 of which are connected to peripheral DMA requests. These come
from the

Flexcomm Interface

s (USART, SPI, I

2

C, and I2S) and digital microphone

interfaces.

•

DMA operations can be triggered by on-chip or off-chip events.

•

Priority is user selectable for each channel (up to eight priority levels).

•

Continuous priority arbitration.

•

Address cache with four entries.

•

Efficient use of data bus.

•

Supports single transfers up to 1,024 words.

•

Address increment options allow packing and/or unpacking data.

«
...
33
34
35
36
37
...
»

Summary of Contents for LPC5411 Series










































































































Reviews:

No comments

Related manuals for LPC5411 Series

Brand: Echelon Pages: 40

Brand: Yudian Pages: 26

Brand: Linak Pages: 2

Brand: intech 21 Pages: 15

Brand: LevelOne Pages: 314

Brand: Beckhoff Pages: 67

Brand: Omron Pages: 12

Brand: Maverick Pages: 122

Brand: Cruisair Pages: 30

Brand: D+H Pages: 20

Brand: Genius Pages: 52

Brand: Linear Technology Pages: 6

Brand: MDT Pages: 51

Brand: ELREHA Pages: 18

Max Charge MC-614-H

Brand: Balmar Pages: 20

Mini-PLC STG-115

Brand: Barth Pages: 8

Compact Embedded Controller LinPAC-8x41

Brand: ICP DAS USA Pages: 13

Brand: Atkinson Electronics Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands